标题: rv1126通过usb接机械硬盘盒 [打印本页] 作者: xinzhiling111 时间: 2021-9-3 16:00 标题: rv1126通过usb接机械硬盘盒 rv1126通过usb接机械硬盘盒，没有挂载成功，从log看disconnect，请问有碰到过的吗？log如下：
[ 1010.752739] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[ 1010.865458] usb 1-1.4: New USB device found, idVendor=152d, idProduct=9561, bcdDevice= 1.05
[ 1010.865497] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1010.865509] usb 1-1.4: Product: JMS56x Series
[ 1010.865519] usb 1-1.4: Manufacturer: JMicron
[ 1010.865536] usb 1-1.4: SerialNumber: 00000000000000000000
[ 1010.867781] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 1010.868361] usb-storage 1-1.4:1.0: Quirks match for vid 152d pid 9561: 4000000
[ 1010.868476] scsi host0: usb-storage 1-1.4:1.0
[ 1011.057551] usb 1-1.4: USB disconnect, device number 7
你也遇到这个问题了吗？作者: xinzhiling111 时间: 2021-9-6 10:17
[ 106.051384] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
[ 106.166502] usb 1-1.4: New USB device found, idVendor=152d, idProduct=9561, bcdDevice= 1.05
[ 106.166583] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 106.166614] usb 1-1.4: Product: JMS56x Series
[ 106.166642] usb 1-1.4: Manufacturer: JMicron
[ 106.166670] usb 1-1.4: SerialNumber: 00000000000000000000
[ 106.171276] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 106.172012] usb-storage 1-1.4:1.0: Quirks match for vid 152d pid 9561: 4000000
[ 106.172270] scsi host0: usb-storage 1-1.4:1.0
[ 107.179608] scsi 0:0:0:0: Direct-Access ST2000VX 000-1ES164 0105 PQ: 0 ANSI: 6
[ 107.180946] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 115.124610] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 115.128056] sd 0:0:0:0: [sda] Write Protect is off
[ 115.128128] sd 0:0:0:0: [sda] Mode Sense: 47 00 10 08
[ 115.129542] sd 0:0:0:0: [sda] No Caching mode page found
[ 115.129620] sd 0:0:0:0: [sda] Assuming drive cache: write through
[ 115.217530] sda: sda1
[ 115.224705] sd 0:0:0:0: [sda] Attached SCSI disk
重新插拔几次，出现上面的打印，看着应该是正常的，用fdisk -l命令，能看到/dev/sda1分区了，但是挂载的时候，用下面命令：
mount /dev/sda1 /media/usb0
mount: mounting /dev/sda1 on /media/usb0 failed: Invalid argument
用-t 指定文件系统类型的话，就会提示failed: No such device，对比看的rk3399pro上挂载的时候不指定-t是可以成功挂载的