Toybrick

标题: 求助！升级固件后，RKDevTool无法发现设备 [打印本页]

作者: zykj 时间: 2022-4-22 14:52
标题: 求助！升级固件后，RKDevTool无法发现设备
本帖最后由 zykj 于 2022-4-22 17:28 编辑

TB-RK3588X开发板，通过RKDevTool升级官网上的linux固件后，RKDevTool提示是升级成功了的。但是重启后发现有无法启动。RKDevTool无法发现设备。

按[size=13.3333px]Recovery键、以及按网上的把EMMC_CLK 时钟线对地短接强制进入maskrom模式的方法都试过了。

请问有什么办法可以解决？

打印如下：

LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-g40801113c5-211215 #zzz (Jan 20 2022 - 11:13:35)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 1
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x2000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(0287c8ddcd...) + OK
## Checking uboot 0x00200000 ... sha256(464f102efd...) + OK
## Checking fdt 0x00308ef0 ... sha256(a5e6b35d32...) + OK
## Checking atf-2 0x000f0000 ... sha256(a923fc5850...) + OK
## Checking atf-3 0xff100000 ... sha256(e0510e813f...) + OK
## Checking atf-4 0xff009000 ... sha256(d55aac40fb...) + OK
## Checking optee 0x08400000 ... sha256(9289764f93...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 86.350 ms

INFO: Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-264-g378cb8595:derrick.huang
NOTICE:  BL31: Built : 20:05:21, Jan 18 2022
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-628-g3f0f0b052 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #4 Fri Jan 14 09:33:37 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9

U-Boot 2017.09-gaaa6bb5a5f-220120 #addy (Jan 21 2022 - 14:06:51 +0800)

Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb6e000
Relocation fdt: eb9fabd0 - eb9fece0
CR: M/C/I
Using default environment

Hotkey: ctrl+q
mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 200Mhz
PartType: EFI
DM: v2
No misc partition
boot mode: None
FIT: No boot partition
153575 bytes read in 6 ms (24.4 MiB/s)
DTB(Distro): /extlinux/toybrick.dtb
spi2: RK806: 2
vdd_gpu_s0 750000 uV
vdd_npu_s0 750000 uV
vdd_vdenc_s0 750000 uV
vdd_gpu_mem_s0 850000 uV
vdd_npu_mem_s0 500000 uV
vdd_vdenc_mem_s0 3275000 uV
Failed to request rk8xx irq, ret=-16
spi2: RKfff: 15
vdd_cpu_big1_s0 3400000 uV
vdd_cpu_big0_s0 3400000 uV
vdd_cpu_lit_s0 3400000 uV
vdd_cpu_big1_mem_s0 3400000 uV
vdd_cpu_big0_mem_s0 3400000 uV
vdd_cpu_lit_mem_s0 3400000 uV

如果不按[size=13.3333px]Recovery键, 可能会一直打印这个：
"Synchronous Abort" handler, esr 0x02000000

¿©KB81@>Õ#B;ÕÀ>Õ@>ÕæÃÑ>Õctioio  = 00000000eb9fa810 = 0000000000000020
* ESR_EL989291284 = 0000000000000000
* Reloc Off  = 00000000edb6e000

x0 : 00000000ede470ac x1 : 00000000ede47097
x2 : 00000000ede470c3 x3 : 00000000ede470e0
x4 : 00000000ede47097 x5 : 0000000000000000
x6 : 00000000ede47148 x7 : 0000000000000000
x8 : 00000000ede470ac x9 : 0000000000000000
x10: 00000000ede47169 x11: 0000000000000000
x12: 0000000000000000 x13: 0000000000000000
x14: 00000000ede47148 x15: 00000000ede471a3
x16: 0000000000000000 x17: 00000000ede47148
x18: 00000000ede47148 x19: 00000000ede471ce
x20: 00000000ede471f9 x21: 0000000000000000
x22: 0000000000000000 x23: 0000000000000000
x24: 0000000000000000 x25: 0000000000000000
x26: 0000000000000000 x27: 00000000ede47234
x28: 00000000ede4725c x29: 00000000ede4725c

ELR(PC) = 00000000feb50000
  0000000000”º>ùA7
   = 00000000feb50000
"Synchronous Abort" handler, esr 0x02000000

作者: mdd 时间: 2022-4-22 17:13
我也遇到同样的问题啊崩溃了
烧完固件就没显示了

作者: toybrick 时间: 2022-4-28 14:19
板子拍照一下

作者: zykj 时间: 2022-5-5 17:14

toybrick 发表于 2022-4-28 14:19
板子拍照一下

已经解决了，maskrom键不明显，之前没找到

作者: zykj 时间: 2022-5-5 17:59

toybrick 发表于 2022-4-28 14:19
板子拍照一下

请问NVR版本的kernel是不是有bug，编译出来的kernel无法正常运行，用官网下载的kernel就没问题：
DDR Version V1.06 20220224
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL board init
U-Boot SPL 2017.09-gbdb740d4da-220216 #cjh (Feb 24 2022 - 03:15:33)
Failed to set cpub01
Failed to set cpub23
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC: no card present
mmc_init: -123, time 0
spl: mmc init failed with error: -123
Trying to boot from MMC1
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(591a33415e...) + OK
## Checking uboot 0x00200000 ... sha256(ab9fb6b10b...) + OK
## Checking fdt 0x0031f3a0 ... sha256(5ded5b9261...) + OK
## Checking atf-2 0x000f0000 ... sha256(5654dd95de...) + OK
## Checking atf-3 0xff100000 ... sha256(ab7f5b01ad...) + OK
## Checking atf-4 0xff009000 ... sha256(2301cf73be...) + OK
## Checking optee 0x08400000 ... sha256(08998eda55...) + OK
Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
Total: 85.107 ms

INFO: Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-310-gb5f843fe1:derrick.huang
NOTICE:  BL31: Built : 12:00:06, Mar  4 2022
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-4
INFO: idle_st=0x21fff, pd_st=0x11fff9
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-632-g9d22c1e96 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #7 Wed Jan 26 16:52:23 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9

U-Boot 2017.09-gc13156be77 #wswu (May 03 2022 - 08:03:49 +0000)

Model: Rockchip RK3588 Evaluation Board
PreSerial: 2, raw, 0xfeb50000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: edb58000
Relocation fdt: eb9fa088 - eb9fece8
CR: M/C/I
Using default environment

mmc@fe2c0000: 1, mmc@fe2e0000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 200Mhz
PartType: EFI
DM: v2
No misc partition
boot mode: normal
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_cpu_big0_s0 800000 uV
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_cpu_big1_s0 800000 uV
I2c2 speed: 100000Hz
vsel-gpios- not found! Error: -2
en-gpios- not found! Error: -2
vdd_npu_s0 800000 uV
spi2: RK806: 2
vdd_gpu_s0 750000 uV
vdd_cpu_lit_s0 750000 uV
vdd_vdenc_s0 init 750000 uV
route node define force_timing, use 1024x768p0 as default mode
get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
route node define force_timing, use 1024x768p0 as default mode
route node define force_timing, use 1024x768p0 as default mode
route node define force_timing, use 1024x768p0 as default mode
Could not find baseparameter partition
Model: Rockchip RK3588 NVR DEMO LP4 V10 Board
Rockchip UBOOT DRM driver version: v1.0.1
vp0 have layer nr:2[0 2 ], primary plane: 2
vp1 have layer nr:2[1 3 ], primary plane: 3
vp2 have layer nr:2[6 8 ], primary plane: 8
vp3 have layer nr:2[7 9 ], primary plane: 9
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
can't get edid block:0
failed to get edid
dp@fde50000: use force output detailed mode clock 65000 kHz, flags[a]
H: 1024 1048 1184 1344
V: 0768 0771 0777 0806
bus_format: 100a
VOP update mode to: 1024x768p0, type: DP0 for VP2
VOP VP2 enable Esmart2[654x270->654x270@185x249] fmt[2] addr[0xedf04000]
training link: 0 lane at 0 MHz
failed to configure DP link: -22
link training failed: -22
failed to enable link: -22
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1024x768 bus_format:0x100a
hdmi@fde80000: use force output detailed mode clock 65000 kHz, flags[a]
H: 1024 1048 1184 1344
V: 0768 0771 0777 0806
bus_format: 100a
VOP update mode to: 1024x768p0, type: HDMI0 for VP2
dclk:65000,if_pixclk_div;2,if_dclk_div:4
hdptx_ropll_cmn_config bus_width:0 rate:650000
hdptx phy pll locked!
VOP VP2 enable Esmart2[654x270->654x270@185x249] fmt[2] addr[0xedf04000]
Non-CEA mode used in HDMI
mtmdsclock:65000000
bus_width:0x9eb10,bit_rate:650000
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
timeout waiting for AUX reply
dw-dp: transaction timed out
can't get edid block:0
failed to get edid
dp@fde60000: use force output detailed mode clock 65000 kHz, flags[a]
H: 1024 1048 1184 1344
V: 0768 0771 0777 0806
bus_format: 100a
VOP update mode to: 1024x768p0, type: DP1 for VP2
VOP VP2 enable Esmart2[654x270->654x270@185x249] fmt[2] addr[0xedf04000]
training link: 0 lane at 0 MHz
failed to configure DP link: -22
link training failed: -22
failed to enable link: -22
i2c read err!
i2c read err!
i2c read err!
i2c read err!
i2c read err!
can't get edid block:0
failed to get edid
Could not find baseparameter partition
color_format:0
hdmi_select_link_config use tmds mode
mode:1024x768 bus_format:0x100a
hdmi@fdea0000: use force output detailed mode clock 65000 kHz, flags[a]
H: 1024 1048 1184 1344
V: 0768 0771 0777 0806
bus_format: 100a
VOP update mode to: 1024x768p0, type: HDMI1 for VP2
dclk:65000,if_pixclk_div;2,if_dclk_div:4
hdptx_ropll_cmn_config bus_width:0 rate:650000
hdptx phy pll locked!
VOP VP2 enable Esmart2[654x270->654x270@185x249] fmt[2] addr[0xedf04000]
Non-CEA mode used in HDMI
mtmdsclock:65000000
bus_width:0x9eb10,bit_rate:650000
hdptx phy lane locked!
dw_hdmi_setup HDMI mode
don't use dsc mode
dw hdmi qp use tmds mode
CLK: (uboot. arm: enter 1200000 KHz, init 1200000 KHz, kernel 0N/A)
  b0pll 1200000 KHz
  b1pll 1200000 KHz
  lpll 1200000 KHz
  v0pll 650000 KHz
  aupll 24000 KHz
  cpll 1500000 KHz
  gpll 1188000 KHz
  npll 850000 KHz
  ppll 100000 KHz
  aclk_center_root 702000 KHz
  pclk_center_root 100000 KHz
  hclk_center_root 396000 KHz
  aclk_center_low_root 500000 KHz
  aclk_top_root 750000 KHz
  pclk_top_root 100000 KHz
  aclk_low_top_root 396000 KHz
No misc partition
Net: eth1: ethernet@fe1c0000, eth0: ethernet@fe1b0000
Hit key to stop autoboot('CTRL+C'):  0
Could not find misc partition
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xeacb4a40 with size 0x00b44600
Fdt Ramdisk skip relocation
No misc partition
## Loading kernel from FIT Image at eacb4a40 ...
Using 'conf' configuration
## Verified-boot: 0
Trying 'kernel' kernel subimage
   Description:  unavailable
   Type:       Kernel Image
   Compression:  lz4 compressed
   Data Start: 0xeacd8a40
   Data Size: 11666511 Bytes = 11.1 MiB
   Architecture: AArch64
   OS:          Linux
   Load Address: 0x00400000
   Entry Point:  0x00400000
   Hash algo: sha256
   Hash value: c9c06a7d46b69845d034a6403b172a2cf62f088b025ad9365accd10ca8754992
Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at eacb4a40 ...
Using 'conf' configuration
Trying 'fdt' fdt subimage
   Description:  unavailable
   Type:       Flat Device Tree
   Compression:  uncompressed
   Data Start: 0xeacb5240
   Data Size: 145245 Bytes = 141.8 KiB
   Architecture: AArch64
   Load Address: 0x0a100000
   Hash algo: sha256
   Hash value: df3e1a6bad7c0242bcfca03e9c32eccb3fa295144b501997f282e13aa9ecc5da
Verifying Hash Integrity ... sha256+ OK
Loading fdt from 0x0a100000 to 0x0a100000
Booting using the fdt blob at 0x0a100000
Uncompressing LZ4 Kernel Image from 0xeacd8a40 to 0x00400000 ... with 01b78808 bytes OK
kernel loaded at 0x00400000, end = 0x01f78808
Using Device Tree in place at 000000000a100000, end 000000000a12675c
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
Total: 1650.535 ms

Starting kernel ...

[ 1.750714] Booting Linux on physical CPU 0x0000000400 [0x414fd0b0]
[ 1.750724] Linux version 5.10.66 (wswu@wswu) (aarch64-linux-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #1 SMP Tue May 3 07:42:53 UTC 2022
[ 1.754061] Machine model: Rockchip RK3588 NVR DEMO LP4 V10 Board
[ 1.754092] earlycon: uart8250 at MMIO32 0x00000000feb50000 (options '')
[ 1.758019] printk: bootconsole [uart8250] enabled
[ 1.760231] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@00000000': base 0x0000000000000000, size 0 MiB
[ 1.761320] Reserved memory: created CMA memory pool at 0x00000001ff800000, size 8 MiB
[ 1.762023] OF: reserved mem: initialized node cma, compatible id shared-dma-pool
[ 1.892060] Zone ranges:
[ 1.892289] DMA    [mem 0x0000000000200000-0x00000000ffffffff]
[ 1.892841] DMA32 empty
[ 1.893097] Normal [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.893646] Movable zone start for each node
[ 1.894023] Early memory node ranges
[ 1.894341] node 0: [mem 0x0000000000200000-0x00000000083fffff]
[ 1.894902] node 0: [mem 0x0000000009400000-0x00000000efffffff]
[ 1.895458] node 0: [mem 0x0000000100000000-0x00000001ffffffff]
[ 1.896020] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[ 1.927130] psci: probing for conduit method from DT.
[ 1.927588] psci: PSCIv1.1 detected in firmware.
[ 1.928002] psci: Using standard PSCI v0.2 function IDs
[ 1.928468] psci: Trusted OS migration not required
[ 1.928905] psci: SMC Calling Convention v1.2
[ 1.929526] percpu: Embedded 30 pages/cpu s84248 r8192 d30440 u122880
[ 1.930157] Detected PIPT I-cache on CPU0
[ 1.930531] CPU features: detected: GIC system register CPU interface
[ 1.931109] CPU features: detected: Virtualization Host Extensions
[ 1.931660] CPU features: detected: Hardware dirty bit management
[ 1.932205] CPU features: detected: Spectre-v4
[ 1.932602] alternatives: patching kernel code
[ 1.933146] Built 1 zonelists, mobility grouping on.  Total pages: 1995336
[ 1.933763] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0xfeb50000 console=ttyFIQ0 irqchip.gicv3_pseudo_nmi=0 clk_gate.always_on=1 pm_domains.always_on=1 root=PARTUUID=614e0000-0000
[ 1.937176] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[ 1.938339] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[ 1.939035] mem auto-init: stack

ff, heap alloc

ff, heap free

ff
[ 1.946791] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[ 1.980997] Memory: 7847468K/8108032K available (14014K kernel code, 3042K rwdata, 5200K rodata, 5824K init, 509K bss, 252372K reserved, 8192K cma-reserved)
[ 1.982294] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 1.982884] ftrace: allocating 52512 entries in 206 pages
[ 2.028325] ftrace: allocated 206 pages with 5 groups
[ 2.028900] rcu: Hierarchical RCU implementation.
[ 2.029322] rcu: RCU event tracing is enabled.
[ 2.029726] Rude variant of Tasks RCU enabled.
[ 2.030130] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[ 2.032264] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 2.033546] GICv3: GIC: Using split EOI/Deactivate mode
[ 2.034015] GICv3: 480 SPIs implemented
[ 2.034357] GICv3: 0 Extended SPIs implemented
[ 2.034766] GICv3: Distributor has no Range Selector support
[ 2.035270] GICv3: 16 PPIs implemented
[ 2.035647] GICv3: CPU0: found redistributor 400 region 0:0x00000000fe700000
[ 2.036324] ITS [mem 0xfe640000-0xfe65ffff]
[ 2.036736] ITS@0x00000000fe640000: allocated 8192 Devices @1001d0000 (indirect, esz 8, psz 64K, shr 0)
[ 2.037594] ITS@0x00000000fe640000: allocated 32768 Interrupt Collections @1001e0000 (flat, esz 2, psz 64K, shr 0)
[ 2.038519] ITS: using cache flushing for cmd queue
[ 2.038968] ITS [mem 0xfe660000-0xfe67ffff]
[ 2.039378] ITS@0x00000000fe660000: allocated 8192 Devices @100200000 (indirect, esz 8, psz 64K, shr 0)
[ 2.040225] ITS@0x00000000fe660000: allocated 32768 Interrupt Collections @100210000 (flat, esz 2, psz 64K, shr 0)
[ 2.041146] ITS: using cache flushing for cmd queue
[ 2.041657] GICv3: using LPI property table @0x0000000100220000
[ 2.042297] GIC: using cache flushing for LPI property table
[ 2.042803] GICv3: CPU0: using allocated LPI pending table @0x0000000100230000
[ 2.043523] random: get_random_bytes called from start_kernel+0x3d8/0x5cc with crng_init=0
[ 2.102292] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 2.103560] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 2.104513] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 2.105651] Console: colour dummy device 80x25
[ 2.106054] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 2.106959] pid_max: default: 32768 minimum: 301
[ 2.107426] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.108106] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 2.109411] rcu: Hierarchical SRCU implementation.
[ 2.110176] Platform MSI: msi-controller@fe640000 domain created
[ 2.110711] Platform MSI: msi-controller@fe660000 domain created
[ 2.111370] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe640000 domain created
[ 2.112103] PCI/MSI: /interrupt-controller@fe600000/msi-controller@fe660000 domain created
[ 2.113020] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 5 initializing
I/TC: Secondary CPU 5 switching to normal world boot
I/TC: Secondary CPU 6 initializing
I/TC: Secondary CPU 6 switching to normal world boot
I/TC: Secondary CPU 7 initializing
I/TC: Secondary CPU 7 switching to normal world boot
I/TC: Secondary CPU 0 initializing
I/TC: Secondary CPU 0 switching to normal world boot
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[ 2.114319] Detected PIPT I-cache on CPU1
[ 2.114339] GICv3: CPU1: found redistributor 500 region 0:0x00000000fe720000
[ 2.114350] GICv3: CPU1: using allocated LPI pending table @0x0000000100240000
[ 2.114378] CPU1: Booted secondary processor 0x0000000500 [0x414fd0b0]
[ 2.115292] Detected PIPT I-cache on CPU2
[ 2.115308] GICv3: CPU2: found redistributor 600 region 0:0x00000000fe740000
[ 2.115318] GICv3: CPU2: using allocated LPI pending table @0x0000000100250000
[ 2.115344] CPU2: Booted secondary processor 0x0000000600 [0x414fd0b0]
[ 2.116240] Detected PIPT I-cache on CPU3
[ 2.116254] GICv3: CPU3: found redistributor 700 region 0:0x00000000fe760000
[ 2.116263] GICv3: CPU3: using allocated LPI pending table @0x0000000100260000
[ 2.116288] CPU3: Booted secondary processor 0x0000000700 [0x414fd0b0]
[ 2.117205] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[ 2.117211] Detected VIPT I-cache on CPU4
[ 2.117239] GICv3: CPU4: found redistributor 0 region 0:0x00000000fe680000
[ 2.117255] GICv3: CPU4: using allocated LPI pending table @0x0000000100270000
[ 2.117295] CPU4: Booted secondary processor 0x0000000000 [0x412fd050]
[ 2.118255] Detected VIPT I-cache on CPU5
[ 2.118284] GICv3: CPU5: found redistributor 100 region 0:0x00000000fe6a0000
[ 2.118300] GICv3: CPU5: using allocated LPI pending table @0x0000000100280000
[ 2.118338] CPU5: Booted secondary processor 0x0000000100 [0x412fd050]
[ 2.119301] Detected VIPT I-cache on CPU6
[ 2.119330] GICv3: CPU6: found redistributor 200 region 0:0x00000000fe6c0000
[ 2.119347] GICv3: CPU6: using allocated LPI pending table @0x0000000100290000
[ 2.119386] CPU6: Booted secondary processor 0x0000000200 [0x412fd050]
[ 2.120351] Detected VIPT I-cache on CPU7
[ 2.120381] GICv3: CPU7: found redistributor 300 region 0:0x00000000fe6e0000
[ 2.120398] GICv3: CPU7: using allocated LPI pending table @0x00000001002a0000
[ 2.120438] CPU7: Booted secondary processor 0x0000000300 [0x412fd050]
[ 2.120537] smp: Brought up 1 node, 8 CPUs
[ 2.136775] SMP: Total of 8 processors activated.
[ 2.137193] CPU features: detected: Privileged Access Never
[ 2.137684] CPU features: detected: User Access Override
[ 2.138154] CPU features: detected: 32-bit EL0 Support
[ 2.138607] CPU
[ 2.204462] rockchip-gpio fd8a0000.gpio: probed /pinctrl/gpio@fd8a0000
[ 2.205221] rockchip-gpio fec20000.gpio: probed /pinctrl/gpio@fec20000
[ 2.205958] rockchip-gpio fec30000.gpio: probed /pinctrl/gpio@fec30000
[ 2.206696] rockchip-gpio fec40000.gpio: probed /pinctrl/gpio@fec40000
[ 2.207463] rockchip-gpio fec50000.gpio: probed /pinctrl/gpio@fec50000
[ 2.208064] rockchip-pinctrl pinctrl: probed pinctrl
[ 2.274525] raid6: neonx8 gen()  6516 MB/s
[ 2.331219] raid6: neonx8 xor()  5494 MB/s
[ 2.387917] raid6: neonx4 gen()  7159 MB/s
[ 2.444616] raid6: neonx4 xor()  5541 MB/s
[ 2.501316] raid6: neonx2 gen()  6735 MB/s
[ 2.558013] raid6: neonx2 xor()  5282 MB/s
[ 2.614711] raid6: neonx1 gen()  5582 MB/s
[ 2.671409] raid6: neonx1 xor()  4329 MB/s
[ 2.728108] raid6: int64x8  gen()  1715 MB/s
[ 2.784815] raid6: int64x8  xor()  1079 MB/s
[ 2.841507] raid6: int64x4  gen()  2137 MB/s
[ 2.898210] raid6: int64x4  xor()  1186 MB/s
[ 2.954905] raid6: int64x2  gen()  3148 MB/s
[ 3.011601] raid6: int64x2  xor()  1731 MB/s
[ 3.068302] raid6: int64x1  gen()  2608 MB/s
[ 3.124997] raid6: int64x1  xor()  1422 MB/s
[ 3.125374] raid6: using algorithm neonx4 gen() 7159 MB/s
[ 3.125852] raid6: .... xor() 5541 MB/s, rmw enabled
[ 3.126290] raid6: using neon recovery algorithm
[ 3.127141] fiq_debugger fiq_debugger.0: IRQ fiq not found
[ 3.127628] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[ 3.128136] fiq_debugger_probe: could not install nmi irq handler
[ [ 3.128712] printk: console [ttyFIQ0] enabled
3.128712] printk: console [ttyFIQ0] enabled
[ 3.129482] printk: bootconsole [uart8250] disabled
[ 3.129482] printk: bootconsole [uart8250] disabled
[ 3.130004] Registered fiq debugger ttyFIQ0
[ 3.130304] vcc3v3_pcie30: supplied by vcc12v_dcin
[ 3.130362] vcc5v0_sys: supplied by vcc12v_dcin
[ 3.130493] vcc5v0_host: supplied by vcc5v0_sys
[ 3.130647] vcc5v0_otg: supplied by vcc5v0_sys
[ 3.130706] vcc_1v1_nldo_s3: supplied by vcc5v0_sys
[ 3.130957] iommu: Default domain type: Translated
[ 3.131017] rk_iommu fdab9000.iommu: version = 2
[ 3.131273] rk_iommu fdb50800.iommu: version = 2
[ 3.131387] rk_iommu fdb60f00.iommu: version = 2
[ 3.131493] rk_iommu fdb70f00.iommu: version = 2
[ 3.131578] rk_iommu fdb90480.iommu: version = 2
[ 3.131651] rk_iommu fdba0800.iommu: version = 2
[ 3.131724] rk_iommu fdba4800.iommu: version = 2
[ 3.131801] rk_iommu fdba8800.iommu: version = 2
[ 3.131875] rk_iommu fdbac800.iommu: version = 2
[ 3.131947] rk_iommu fdbb0800.iommu: version = 2
[ 3.132051] rk_iommu fdbdf000.iommu: version = 2
[ 3.132180] rk_iommu fdbef000.iommu: version = 2
[ 3.132307] rk_iommu fdc38700.iommu: version = 2
[ 3.132423] rk_iommu fdc48700.iommu: version = 2
[ 3.132498] rk_iommu fdd97e00.iommu: version = 2
[ 3.132735] SCSI subsystem initialized
[ 3.132799] usbcore: registered new interface driver usbfs
[ 3.132811] usbcore: registered new interface driver hub
[ 3.132836] usbcore: registered new device driver usb
[ 3.132864] mc: Linux media interface: v0.10
[ 3.132874] videodev: Linux video capture interface: v2.00
[ 3.132895] pps_core: LinuxPPS API ver. 1 registered
[ 3.132898] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 3.132904] PTP clock support registered
[ 3.133195] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[ 3.133229] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[ 3.134142] Advanced Linux Sound Architecture Driver Initialized.
[ 3.135564] rockchip-cpuinfo cpuinfo: SoC : 35880000
[ 3.135570] rockchip-cpuinfo cpuinfo: Serial : 0340383263d2d6cd
[ 3.135873] clocksource: Switched to clocksource arch_sys_counter
[ 3.377020] NET: Registered protocol family 2
[ 3.377180] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[ 3.378706] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
[ 3.378762] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[ 3.379035] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes, linear)
[ 3.379564] TCP: Hash tables configured (established 65536 bind 65536)
[ 3.379611] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 3.379707] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
[ 3.379852] NET: Registered protocol family 1
[ 3.380162] RPC: Registered named UNIX socket transport module.
[ 3.380169] RPC: Registered udp transport module.
[ 3.380172] RPC: Registered tcp transport module.
[ 3.380175] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 3.380552] PCI: CLS 0 bytes, default 64
[ 3.381425] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 3.383742] Initialise system trusted keyrings
[ 3.383841] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[ 3.385388] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 3.385642] NFS: Registering the id_resolver key type
[ 3.385652] Key type id_resolver registered
[ 3.385655] Key type id_legacy registered
[ 3.385668] ntfs: driver 2.1.32 [Flags: R/O].
[ 3.385713] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 3.385802] fuse: init (API version 7.32)
[ 3.385933] SGI XFS with security attributes, no debug enabled
[ 3.402053] NET: Registered protocol family 38
[ 3.402061] xor: measuring software checksum speed
[ 3.403283] 8regs          :  8117 MB/sec
[ 3.404199] 32regs       : 10792 MB/sec
[ 3.404950] arm64_neon    : 13186 MB/sec
[ 3.404954] xor: using function: arm64_neon (13186 MB/sec)
[ 3.404959] async_tx: api initialized (async)
[ 3.404962] Key type asymmetric registered
[ 3.404966] Asymmetric key parser 'x509' registered
[ 3.404982] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 3.404986] io scheduler mq-deadline registered
[ 3.404989] io scheduler kyber registered
[ 3.413385] rockchip-hdptx-phy-hdmi fed60000.hdmiphy: hdptx phy init success
[ 3.414135] rockchip-hdptx-phy-hdmi fed70000.hdmiphy: hdptx phy init success
[ 3.415781] rk-pcie fe150000.pcie: invalid prsnt-gpios property in node
[ 63.419185] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[ 63.419195] rcu: 0-...0: (1 GPs behind) idle=baa/1/0x4000000000000000 softirq=18/19 fqs=6000
[ 63.419200] (detected by 1, t=18002 jiffies, g=-1167, q=11)
[ 63.419203] Task dump for CPU 0:
[ 63.419207] task:swapper/0    state:R  running task    stack: 0 pid: 1 ppid:    0 flags:0x0000000a
[ 63.419214] Call trace:
[ 63.419223]  __switch_to+0x134/0x1a4
[ 63.419227]  0xffffffc011c4b9b8
[  243.435813] rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[  243.435820] rcu: 0-...0: (1 GPs behind) idle=baa/1/0x4000000000000000 softirq=18/19 fqs=24002
[  243.435824] (detected by 1, t=72007 jiffies, g=-1167, q=11)
[  243.435827] Task dump for CPU 0:
[  243.435829] task:swapper/0    state:R  running task    stack: 0 pid: 1 ppid:    0 flags:0x0000000a
[  243.435835] Call trace:
[  243.435839]  __switch_to+0x134/0x1a4
[  243.435842]  0xffffffc011c4b9b8

欢迎光临 Toybrick (https://t.rock-chips.com/)