Toybrick

标题: TB-RK3568X烧录官方Linux固件失败 [打印本页]

作者: a14680024 时间: 2025-6-19 11:57
标题: TB-RK3568X烧录官方Linux固件失败
1、我下载了RK3568官方Linux固件包，然后按照教程烧录镜像
烧录完毕后，用串口打开，但是串口卡在这了

cs1, DQS3:cyc:3,oph:1,dll:24
out
U-Boot SPL board init
U-Boot SPL 2017.09-ga1f6fc00a0-210413 #ldq (Apr 13 2021 - 11:35:00)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
No misc partition
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256+ OK
## Checking uboot 0x00a00000 ... sha256+ OK
## Checking fdt 0x00b2a158 ... sha256+ OK
## Checking atf-2 0xfdcc9000 ... sha256+ OK
## Checking atf-3 0xfdcd0000 ... sha256+ OK
## Checking optee 0x08400000 ... sha256+ OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 210.199 ms

INFO: Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-135-**a1658bc-dirty:xsf
NOTICE:  BL31: Built : 19:32:20, Jun  2 2021
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: pmu v1 is valid
INFO: dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO: dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO: dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO: dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
I/TC:
I/TC: Start rockchip platform init
I/TC: Rockchip release version: 1.0
I/TC: OP-TEE version: 3.6.0-307-g0b06ae94 #1 Fri May  7 01:52:27 UTC 2021 aarch64
I/TC: Initialized
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9

U-Boot 2017.09-gc350076109-220518-dirty #chensq (May 18 2022 - 12:32:41 +0800)

Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM:  4 GiB
Sysmem: init
Relocation Offset: ed34e000
Relocation fdt: eb9f8e30 - eb9fecd8
CR: M/C/I
Using default environment

Hotkey: ctrl+s
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
No misc partition
boot mode: normal
FIT: No boot partition
** File not found /extlinux/toybrick.dtb **
No resource partition
No resource partition
Failed to load DTB, ret=-19
Failed to get kernel dtb, ret=-19
io-domain: OK
Failed to get scmi clk dev
Model: Rockchip RK3568 Evaluation Board
rockchip_set_serialno: could not find efuse/otp device
Load sn form vendor failed
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Load SnMacAc from rpmb failed
No SnMacAc found in vendor and rpmb, goto loader ...
RKUSB: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x3a4a000
-

要如何解决啊

作者: jax.fang 时间: 2025-6-20 08:46
有做擦除flash操作吗, 看log是无SN导致进loader模式

作者: a14680024 时间: 2025-6-20 11:08

jax.fang 发表于 2025-6-20 08:46
有做擦除flash操作吗, 看log是无SN导致进loader模式

官方例子是分包烧录的，如何擦除flash

作者: jefferyzhang 时间: 2025-6-20 17:11

a14680024 发表于 2025-6-20 11:08
官方例子是分包烧录的，如何擦除flash

板子是谁家买的，长什么样拍个照看下

作者: a14680024 时间: 2025-6-24 10:48

jefferyzhang 发表于 2025-6-20 17:11
板子是谁家买的，长什么样拍个照看下

file:///C:/Users/ny/Desktop/%E5%BE%AE%E4%BF%A1%E5%9B%BE%E7%89%87_20250624104810.jpg

作者: a14680024 时间: 2025-6-24 10:51

jefferyzhang 发表于 2025-6-20 17:11
板子是谁家买的，长什么样拍个照看下

官方的

作者: jefferyzhang 时间: 2025-6-24 15:41
刚拿回来时候是否开的了机？建议你跟购买的客服聊下，
如果是他们问题就让他们换货。
如果是自己擦掉了SN也可以联系他们重烧下SN。

作者: a14680024 时间: 2025-6-24 18:59

jefferyzhang 发表于 2025-6-24 15:41
刚拿回来时候是否开的了机？建议你跟购买的客服聊下，
如果是他们问题就让他们换货。
如果是自己擦掉了SN也 ...

开的了，我不用官方固件，自己重新编译固件后，烧录能够成功运行linux系统，不明白为什么官方的不行

欢迎光临 Toybrick (https://t.rock-chips.com/)