RV1126烧写内核以后无法正常启动

启动日志如下：

1. => DDR Version V1.05 20201214
   
2. DDR4, 328MHz
   
3. BW=32 Col=10 Bk=4 BG=2 CS0 Row=16 CS=1 Die BW=16 Size=2048MB
   
4. change to: 328MHz
   
5. change to: 528MHz
   
6. change to: 784MHz
   
7. change to: 1056MHz(final freq)
   
8. out
   
9. U-Boot SPL board init
   
10. U-Boot SPL 2017.09-gbf8034353d-201209 #ldq (Dec 10 2020 - 15:35:41)
    
11. unknown raw ID phN
    
12. unrecognized JEDEC id bytes: 00, 00, 00
    
13. Trying to boot from MMC2
    
14. Card did not respond to voltage select!
    
15. mmc_init: -95, time 9
    
16. spl: mmc init failed with error: -95
    
17. Trying to boot from MMC1
    
18. Magic is incorrect.
    
19. Error validating A/B metadata from disk. Resetting and writing new A/B metadata to disk.
    
20. ## Verified-boot: 0
    
21. ## Checking optee 0x08400000 ... sha256+ OK
    
22. ## Checking uboot 0x00400000 ... sha256+ OK
    
23. ## Checking fdt 0x004b5e7c ... sha256+ OK
    
24. Jumping to U-Boot(0x00400000) via OP-TEE(0x08400000)
    
25. Total: 146.96 ms
    
26. 
    
27. I/TC:
    
28. I/TC: cpu feature:0x0
    
29. I/TC: cpu_st=0xe0
    
30. I/TC: OP-TEE version: 3.6.0-315-g715df903 #2 Wed Apr 28 01:43:37 UTC 2021 arm
    
31. I/TC: Next entry point address: 0x00400000
    
32. I/TC: Initialized
    
33. 
    
34. 
    
35. U-Boot 2017.09-g09fb47fbbb-210616 #chenyf (Jun 17 2021 - 08:26:18 +0800)
    
36. 
    
37. Model: Rockchip RV1126 Evaluation Board
    
38. PreSerial: 2, raw, 0xff570000
    
39. DRAM:  2 GiB
    
40. Sysmem: init
    
41. Relocation Offset: 00000000, fdt: 7bbf9c58
    
42. Using default environment
    
43. 
    
44. dwmmc@ffc50000: 0, dwmmc@ffc60000: 1
    
45. Bootdev(atags): mmc 0
    
46. MMC0: HS200, 200Mhz
    
47. PartType: EFI
    
48. boot mode: None
    
49. FIT: No boot partition
    
50. Get board-id node failed
    
51. Failed to mount ext2 filesystem...
    
52. ** Unrecognized filesystem type **
    
53. No resource partition
    
54. Failed to load DTB
    
55. Failed to get kernel dtb, ret=-19
    
56. io-domain: OK
    
57. Model: Rockchip RV1126 Evaluation Board
    
58. Load SnMacAc from vendor: sn TRs11264210600136, mac 10dcb6905481
    
59. optee api revision: 2.0
    
60. TEEC: Waring: Could not find security partition
    
61. Load SnMacAc from rpmb: sn TRs11264210600136, mac 10dcb6905481
    
62. Toybrick check SnMacAc OK, sn TRs11264210600136
    
63. CLK: (sync kernel. arm: enter 1008000 KHz, init 816000 KHz, kernel 0N/A)
    
64.   apll 816000 KHz
    
65.   dpll 528000 KHz
    
66.   gpll 1188000 KHz
    
67.   cpll 500000 KHz
    
68.   hpll 1400000 KHz
    
69.   aclk_pdbus 500000 KHz
    
70.   hclk_pdbus 198000 KHz
    
71.   pclk_pdbus 99000 KHz
    
72.   aclk_pdphp 297000 KHz
    
73.   hclk_pdphp 198000 KHz
    
74.   hclk_pdaudio 148500 KHz
    
75.   hclk_pdcore 198000 KHz
    
76.   pclk_pdpmu 99000 KHz
    
77. Net:   eth0: ethernet@ffc40000
    
78. Hit key to stop autoboot('CTRL+C'):  0
    
79. ## Booting FIT Image FIT: No boot partition
    
80. FIT: No FIT image
    
81. ANDROID: reboot reason: "(none)"
    
82. android_image_load_by_partname: Can't find part: boot
    
83. Android image load failed
    
84. Android boot failed, error -1.
    
85. MMC error: The cmd index is 1, ret is -110
    
86. Card did not respond to voltage select!
    
87. mmc_init: -95, time 9
    
88. switch to partitions #0, OK
    
89. mmc0(part 0) is current device
    
90. Failed to mount ext2 filesystem...
    
91. ** Unrecognized filesystem type **
    
92. MMC error: The cmd index is 1, ret is -110
    
93. Card did not respond to voltage select!
    
94. mmc_init: -95, time 9
    
95. ** Bad device mmc 1 **
    
96. MMC error: The cmd index is 1, ret is -110
    
97. Card did not respond to voltage select!
    
98. mmc_init: -95, time 10
    
99. ** Bad device mmc 1 **
    
100. Failed to mount ext2 filesystem...
     
101. ** Unrecognized filesystem type **
     
102. starting USB...
     
103. Bus dwc3@ffd00000: Register 1000140 NbrPorts 1
     
104. Starting the controller
     
105. USB XHCI 1.10
     
106. scanning bus dwc3@ffd00000 for devices... 1 USB Device(s) found
     
107.        scanning usb for storage devices... 0 Storage Device(s) found
     
108. 
     
109. Device 0: unknown device
     
110. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
111. missing environment variable: pxeuuid
     
112. missing environment variable: bootfile
     
113. Retrieving file: pxelinux.cfg/01-10-dc-b6-90-54-81
     
114. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
115. missing environment variable: bootfile
     
116. Retrieving file: pxelinux.cfg/00000000
     
117. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
118. missing environment variable: bootfile
     
119. Retrieving file: pxelinux.cfg/0000000
     
120. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
121. missing environment variable: bootfile
     
122. Retrieving file: pxelinux.cfg/000000
     
123. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
124. missing environment variable: bootfile
     
125. Retrieving file: pxelinux.cfg/00000
     
126. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
127. missing environment variable: bootfile
     
128. Retrieving file: pxelinux.cfg/0000
     
129. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
130. missing environment variable: bootfile
     
131. Retrieving file: pxelinux.cfg/000
     
132. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
133. missing environment variable: bootfile
     
134. Retrieving file: pxelinux.cfg/00
     
135. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
136. missing environment variable: bootfile
     
137. Retrieving file: pxelinux.cfg/0
     
138. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
139. missing environment variable: bootfile
     
140. Retrieving file: pxelinux.cfg/default-arm-rockchip
     
141. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
142. missing environment variable: bootfile
     
143. Retrieving file: pxelinux.cfg/default-arm
     
144. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
145. missing environment variable: bootfile
     
146. Retrieving file: pxelinux.cfg/default
     
147. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     
148. Config file not found
     
149. EQOS_DMA_MODE_SWR stuckFAILED: 0rv1126_set_rgmii_speed can't get clk_mac_speed clock (ret=-61):
     

复制代码烧写日志如下：

1. 10:28:30 409        瑞芯微开发工具 v2.7.1.0 start run
   
2. 10:28:47 114        瑞芯微开发工具 v2.7.1.0 start run
   
3. 10:32:59 839        Layer<1-2-1>:测试设备开始
   
4. 10:32:59 841        Layer<1-2-1>:测试设备成功
   
5. 10:32:59 845        Layer<1-2-1>: Download boot_linux at 0x00006000...
   
6. 10:33:02 442        Layer<1-2-1>: RunProc is ending, ret=1
   

复制代码请版主大大指导一下该怎么搞，谢谢！