【入门】rk3568上用usb连接的rk1808m0

才接触rk1808m0，想请问下，在rk3568 linux开发板上，插入usb3.0的rk1808m0小板，需要加载些什么驱动才能完整使用rk1808m0（需要配置哪些config）

当前插入后的log如下

1. [root@rk3568:/]# [  118.666735] usb 6-1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
   
2. [  118.686052] usb 6-1: New USB device found, idVendor=2207, idProduct=0018, bcdDevice= 0.00
   
3. [  118.686238] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
   
4. [  118.686277] usb 6-1: Product: TB-RK1808M0
   
5. [  118.686325] usb 6-1: Manufacturer: rockchip
   
6. [  118.686414] usb 6-1: SerialNumber: TM018084220400124
   
7. [  118.738414] usb-storage 6-1:1.0: USB Mass Storage device detected
   
8. [  118.739095] scsi host0: usb-storage 6-1:1.0
   
9. [  119.755368] scsi 0:0:0:0: Direct-Access     Linux    File-Stor Gadget 0404 PQ: 0 ANSI: 2
   
10. [  119.757152] sd 0:0:0:0: Attached scsi generic sg0 type 0
    
11. [  119.758074] sd 0:0:0:0: Power-on or device reset occurred
    
12. [  119.759155] sd 0:0:0:0: [sda] 20480 512-byte logical blocks: (10.5 MB/10.0 MiB)
    
13. [  119.759867] sd 0:0:0:0: [sda] Write Protect is on
    
14. [  119.760679] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
    
15. [  119.767030]  sda:
    
16. [  119.769082] sd 0:0:0:0: [sda] Attached SCSI removable disk
    
17. [  119.862996] FAT-fs (sda): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
    
18. 
    
19. [root@rk3568:/]#
    
20. [root@rk3568:/]# ifconfig
    
21. eth0      Link encap:Ethernet  HWaddr CA:97:2A:AD:B5:0F  
    
22.           UP BROADCAST MULTICAST  MTU:1500  Metric:1
    
23.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    
24.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    
25.           collisions:0 txqueuelen:1000
    
26.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
    
27.           Interrupt:17
    
28. 
    
29. eth1      Link encap:Ethernet  HWaddr C6:97:2A:AD:B5:0F  
    
30.           UP BROADCAST MULTICAST  MTU:1500  Metric:1
    
31.           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    
32.           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    
33.           collisions:0 txqueuelen:1000
    
34.           RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
    
35.           Interrupt:27
    
36. 
    
37. lo        Link encap:Local Loopback  
    
38.           inet addr:127.0.0.1  Mask:255.0.0.0
    
39.           inet6 addr: ::1/128 Scope:Host
    
40.           UP LOOPBACK RUNNING  MTU:65536  Metric:1
    
41.           RX packets:86 errors:0 dropped:0 overruns:0 frame:0
    
42.           TX packets:86 errors:0 dropped:0 overruns:0 carrier:0
    
43.           collisions:0 txqueuelen:1000
    
44.           RX bytes:5608 (5.4 KiB)  TX bytes:5608 (5.4 KiB)
    

复制代码

另外请问有没有一些入门的文档，淘宝官网买了东西以后，两眼一抹黑，不知从何下手，请指教，谢谢呀

可以先查看一下wiki的文档