Toybrick

Toybrick»开源社区 › 开源板 › TB-RK3576D › 使用官方提供的EMMC_UFS固件烧录后，无法正常开机 ...

使用官方提供的EMMC_UFS固件烧录后，无法正常开机

rt3628

注册会员

积分
157
楼主
发表于 3 天前    查看: 36|回复: 0 | [复制链接]    打印 | 只看该作者
使用 UFS 小卡烧录后会一直重开机
无法正常进入系统
  1. Boot0:Mar  1 2024 18:55:39, ver: 0.00
  2. DDR 81dd75088a wesley.yao 24/04/16-11:19:41,fwver: v1.03
  3. In
  4. LPDDR4X, 2112MHz
  5. channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
  6. channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
  7. Manufacturer ID:0xff
  8. CH0 RX Vref:25.7%, RX DQS Vref:31.2%, TX Vref:20.8%,21.8%
  9. DQ roc:
  10. p1 n1, p0 n0, p0 n0, p0 n1, p0 n0, p3 n1, p0 n0, p0 n2, p3 n0,
  11. p5 n2, p2 n0, p2 n0, p0 n5, p0 n6, p1 n1, p1 n0, p0 n0, p6 n0,
  12. DQ rds:
  13. h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
  14. h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
  15. DQS roc: p0 n1, p0, n0

  17. CH1 RX Vref:26.5%, RX DQS Vref:31.6%, TX Vref:22.8%,23.8%
  18. DQ roc:
  19. p3 n0, p5 n0, p6 n0, p1 n0, p0 n7, p5 n0, p6 n0, p4 n1, p4 n0,
  20. p3 n0, p3 n0, p3 n0, p7 n0, p6 n0, p5 n0, p6 n0, p5 n0, p6 n0,
  21. DQ rds:
  22. h1 l0, h1 l0, h1 l0, h0 l0, h0 l0, h1 l0, h1 l0, h0 l0,
  23. h1 l0, h1 l0, h0 l0, h0 l0, h1 l0, h0 l0, h1 l0, h0 l0,
  24. DQS roc: p2 n0, p2, n0

  26. stride=0x3, ddr_config=0x4
  27. hash bank_mask0-3 0x0 0x880 0x1100 0x2200, rank_mask0 0x400400
  28. change to F1: 528MHz
  29. change to F2: 1068MHz
  30. change to F3: 1560MHz
  31. change to F0: 2112MHz
  32. out
  33. U-Boot SPL board init
  34. U-Boot SPL 2017.09-ge53b21c53e6-240430 #lxh (Apr 30 2024 - 15:30:38), fwver: v1.03
  35. unknown raw ID 0 0 0
  36. unrecognized JEDEC id bytes: 00, 00, 00
  37. Device at ufs@2a2d0000 up at:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
  38. Trying to boot from MMC2
  39. MMC: no card present
  40. mmc_init: -123, time 1
  41. spl: mmc init failed with error: -123
  42. Trying to boot from UFS
  43. scanning bus for devices...
  44.   Device 0: (0:0) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  45.             Type: Hard Disk
  46.             Capacity: 122008.0 MB = 119.1 GB (249872384 x 512)
  47.   Device 0: (0:1) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  48.             Type: Hard Disk
  49.             Capacity: 4.0 MB = 0.0 GB (8192 x 512)
  50.   Device 0: (0:2) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  51.             Type: Hard Disk
  52.             Capacity: 4.0 MB = 0.0 GB (8192 x 512)
  53.   Device 0: (0:3) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  54.             Type: Hard Disk
  55.             Capacity: 8.0 MB = 0.0 GB (16384 x 512)
  56. SPL: A/B-slot: _a, successful: 0, tries-remain: 7
  57. Trying fit image at 0x2000 sector
  58. ## Verified-boot: 0
  59. ## Checking atf-1 0x40040000 ... sha256(e238bcae46...) + OK
  60. ## Checking uboot 0x40200000 ... sha256(9a9d5ade77...) + OK
  61. ## Checking fdt 0x40341eb8 ... sha256(6d0c8a3eca...) + OK
  62. ## Checking atf-2 0x400f0000 ... sha256(1cc4399eab...) + OK
  63. ## Checking atf-3 0x3fe70000 ... sha256(3dfdd49eae...) + OK
  64. ## Checking optee 0x48400000 ... sha256(988a2a2a76...) + OK
  65. Jumping to U-Boot(0x40200000) via ARM Trusted Firmware(0x40040000)
  66. Total: 139.841/694.113 ms

  68. INFO:    Preloader serial: 0
  69. NOTICE:  BL31: v2.3():v2.3-763-g76e9c9f54:finley.xiao, fwver: v1.05
  70. NOTICE:  BL31: Built : 14:32:33, Apr 26 2024
  71. INFO:    ext 32k is detected
  72. INFO:    ARM GICv2 driver initialized
  73. INFO:    dfs DDR fsp_params[0].freq_mhz= 2112MHz
  74. INFO:    dfs DDR fsp_params[1].freq_mhz= 528MHz
  75. INFO:    dfs DDR fsp_params[2].freq_mhz= 1068MHz
  76. INFO:    dfs DDR fsp_params[3].freq_mhz= 1560MHz
  77. INFO:    Using opteed sec cpu_context!
  78. INFO:    boot cpu mask: 1
  79. INFO:    BL31: Initializing runtime services
  80. INFO:    BL31: Initializing BL32
  81. I/TC:
  82. I/TC: OP-TEE version: 3.13.0-795-gb90c1680e #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Mon May 13 14:42:41 CST 2024 aarch64, fwver: v1.02
  83. I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000
  84. I/TC: Primary CPU initializing
  85. I/TC: Primary CPU switching to normal world boot
  86. INFO:    BL31: Preparing for EL3 exit to normal world
  87. INFO:    Entry point address = 0x40200000
  88. INFO:    SPSR = 0x3c9


  91. U-Boot 2017.09-g3d9aaf2591-240509-dirty # (May 15 2024 - 11:17:03 +0800)

  93. Model: Rockchip RK3576 Evaluation board
  94. MPIDR: 0x0
  95. PreSerial: 0, raw, 0x2ad40000
  96. DRAM:  8 GiB
  97. Sysmem: init
  98. Relocation Offset: bda1c000
  99. Relocation fdt: fb9f9b90 - fb9fecd8
  100. CR: M/C/I
  101. Using default environment

  103. optee api revision: 2.0
  104. scanning bus for devices...
  105. Device at ufs@2a2d0000 up at:[RX, TX]: gear=[3, 3], lane[2, 2], pwr[FAST MODE, FAST MODE], rate = 2
  106.   Device 0: (0:0) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  107.             Type: Hard Disk
  108.             Capacity: 122008.0 MB = 119.1 GB (249872384 x 512)
  109.   Device 0: (0:1) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  110.             Type: Hard Disk
  111.             Capacity: 4.0 MB = 0.0 GB (8192 x 512)
  112.   Device 0: (0:2) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  113.             Type: Hard Disk
  114.             Capacity: 4.0 MB = 0.0 GB (8192 x 512)
  115.   Device 0: (0:3) Vendor: SAMSUNG Prod.: KLUDG2R1DE-B0F1 Rev: 0100
  116.             Type: Hard Disk
  117.             Capacity: 8.0 MB = 0.0 GB (16384 x 512)
  118. Bootdev(atags): scsi 0
  119. PartType: EFI
  120. TEEC: Waring: Could not find security partition
  121. DM: v2
  122. Failed to mount ext2 filesystem...
  123. ** Unrecognized filesystem type **
  124. boot mode: None
  125. RESC: 'boot', blk@0x0001fafa
  126. resource: sha256+
  127. FIT: no signed, no conf required
  128. DTB: rk-kernel.dtb
  129. HASH(ce): OK
  130. Error binding driver 'dwc3-generic-wrapper': -6
  131. Some drivers failed to bind
  132. I2c1 speed: 100000Hz
  133. PMIC:  RK8060 (on=0x40, off=0x00)
  134. vdd_cpu_big_s0 init 850000 uV
  135. vdd_npu_s0 750000 uV
  136. vdd_cpu_lit_s0 init 850000 uV
  137. vdd_gpu_s0 init 750000 uV
  138. vdd_logic_s0 init 750000 uV
  139. vdd_ddr_s0 850000 uV
  140. Could not find baseparameter partition
  141. Model: Rockchip RK3576 TOYBRICK D0 Board
  142. Rockchip UBOOT DRM driver version: v1.0.1
  143. Assign plane mask automatically
  144. VOP have 1 active VP
  145. vp0 have layer nr:1[2 ], primary plane: 2
  146. vp1 have layer nr:0[], primary plane: 0
  147. vp2 have layer nr:0[], primary plane: 0
  148. Monitor has basic audio support
  149. Could not find baseparameter partition
  150. color_format:0
  151. hdmi_select_link_config use tmds mode
  152. mode:1920x1080 bus_format:0x100a
  153. hdmi@27da0000:  detailed mode clock 148500 kHz, flags[5]
  154.     H: 1920 2008 2052 2200
  155.     V: 1080 1084 1089 1125
  156. bus_format: 100a
  157. VOP update mode to: 1920x1080p60, type: HDMI0 for VP0
  158. disp_info is empty
  159. hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
  160. hdptx phy pll locked!
  161. VP0 set crtc_clock to 1485KHz
  162. Unsupported bt709f at 10bit csc depth, use bt601f instead
  163. VOP VP0 enable Esmart0[654x270->654x270@633x405] fmt[0] addr[0xfdf00000]
  164. CEA mode used vic=16
  165. mtmdsclock:148500000
  166. hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
  167. hdptx phy pll locked!
  168. dw_hdmi_setup HDMI mode
  169. don't use dsc mode
  170. dw hdmi qp use tmds mode
  171. bus_width:0x16a8c8,bit_rate:1485000
  172. hdptx phy lane locked!
  173. Load SnMac from vendor: sn TD080B62800098, mac 10dcb69184f4
  174. Toybrick check SnMac OK, sn TD080B62800098
  175. CLK: (uboot. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
  176.   bpll 816000 KHz
  177.   lpll 816000 KHz
  178.   vpll 594000 KHz
  179.   aupll 786432 KHz
  180.   cpll 1000000 KHz
  181.   gpll 1188000 KHz
  182.   ppll 1300000 KHz
  183.   aclk_bus_root 396000 KHz
  184.   pclk_bus_root 100000 KHz
  185.   hclk_bus_root 198000 KHz
  186.   aclk_top 786432 KHz
  187.   aclk_top_mid 396000 KHz
  188.   pclk_top 100000 KHz
  189.   hclk_top 200000 KHz
  190. Net:   Net Initialization Skipped
  191. No ethernet found.
  192. Hit key to stop autoboot('CTRL+C'):  0
  193. ANDROID: reboot reason: "(none)"
  194. Not AVB images, AVB skip
  195. No valid android hdr
  196. Android image load failed
  197. Android boot failed, error -1.
  198. ## Booting FIT Image at 0xf9099780 with size 0x0275f400
  199. Fdt Ramdisk skip relocation
  200. ## Loading kernel from FIT Image at f9099780 ...
  201.    Using 'conf' configuration
  202. ## Verified-boot: 0
  203.    Trying 'kernel' kernel subimage
  204.      Description:  unavailable
  205.      Type:         Kernel Image
  206.      Compression:  uncompressed
  207.      Data Start:   0xf90dc980
  208.      Data Size:    41009664 Bytes = 39.1 MiB
  209.      Architecture: AArch64
  210.      OS:           Linux
  211.      Load Address: 0x40400000
  212.      Entry Point:  0x40400000
  213.      Hash algo:    sha256
  214.      Hash value:   b194e53a37f440476b7e261b086636f1e74b3ae8e419a1139fc984c8750682c0
  215.    Verifying Hash Integrity ... sha256+ OK
  216. ## Loading fdt from FIT Image at f9099780 ...
  217.    Using 'conf' configuration
  218.    Trying 'fdt' fdt subimage
  219.      Description:  unavailable
  220.      Type:         Flat Device Tree
  221.      Compression:  uncompressed
  222.      Data Start:   0xf909a780
  223.      Data Size:    270370 Bytes = 264 KiB
  224.      Architecture: AArch64
  225.      Load Address: 0x48300000
  226.      Hash algo:    sha256
  227.      Hash value:   ac4b188e1461558be714c71fd07ed0c8adc956ce3f26e22cc44d182d1a8622a0
  228.    Verifying Hash Integrity ... sha256+ OK
  229.    Loading fdt from 0x48300000 to 0x48300000
  230.    Booting using the fdt blob at 0x48300000
  231.    Loading Kernel Image from 0xf90dc980 to 0x40400000 ... OK
  232.    kernel loaded at 0x40400000, end = 0x42b1c200
  233.    Using Device Tree in place at 0000000048300000, end 0000000048345021
  234. vp0, plane_mask:0x4, primary-id:2, curser-id:-1
  235. vp1, plane_mask:0x0, primary-id:0, curser-id:-1
  236. vp2, plane_mask:0x0, primary-id:0, curser-id:-1
  237. ## reserved-memory:
  238.   drm-logo@0: addr=fdf00000 size=15a000
  239.   ramoops@40110000: addr=40110000 size=e0000
  240.   vendor-storage-rm@00000000: addr=fbd24000 size=10000
  241. Adding bank: 0x40200000 - 0x48400000 (size: 0x08200000)
  242. Adding bank: 0x49400000 - 0x100000000 (size: 0xb6c00000)
  243. Adding bank: 0x100000000 - 0x240000000 (size: 0x140000000)
  244. Total: 752.425/790.858 ms

  246. Starting kernel ...

  248. [    0.797049] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
  249. [    0.797072] Linux version 6.1.75 (pzc@inno) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 10.3.1 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #23 SMP Fri Sep  6 15:30:08 CST 2024
  250. [    0.799770] random: crng init done
  251. [    0.804141] Machine model: Rockchip RK3576 TOYBRICK D0 Board
  252. [    0.816234] earlycon: uart8250 at MMIO32 0x000000002ad40000 (options '')
  253. [    0.820740] printk: bootconsole [uart8250] enabled
  254. [    0.823395] efi: UEFI not found.
  255. [    0.825877] OF: fdt: Reserved memory: failed to reserve memory for node 'drm-cubic-lut@0': base 0x0000000000000000, size 0 MiB
  256. [    0.969790] Zone ranges:
  257. [    0.970044]   DMA      [mem 0x0000000040200000-0x00000000ffffffff]
  258. [    0.970631]   DMA32    empty
  259. [    0.970904]   Normal   [mem 0x0000000100000000-0x000000023fffffff]
  260. [    0.971487] Movable zone start for each node
  261. [    0.971888] Early memory node ranges
  262. [    0.972224]   node   0: [mem 0x0000000040200000-0x00000000483fffff]
  263. [    0.972816]   node   0: [mem 0x0000000049400000-0x000000023fffffff]
  264. [    0.973410] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff]
  265. [    0.974640] On node 0, zone DMA: 512 pages in unavailable ranges
  266. [    0.986807] On node 0, zone DMA: 4096 pages in unavailable ranges
  267. [    1.008428] cma: Reserved 16 MiB at 0x00000000ff000000
  268. [    1.009614] psci: probing for conduit method from DT.
  269. [    1.010096] psci: PSCIv1.1 detected in firmware.
  270. [    1.010532] psci: Using standard PSCI v0.2 function IDs
  271. [    1.011026] psci: Trusted OS migration not required
  272. [    1.011492] psci: SMC Calling Convention v1.2
  273. [    1.012204] percpu: Embedded 26 pages/cpu s68968 r8192 d29336 u106496
  274. [    1.012942] Detected VIPT I-cache on CPU0
  275. [    1.013362] CPU features: detected: ARM erratum 845719
  276. [    1.013847] alternatives: applying boot alternatives
  277. [    1.014665] Built 1 zonelists, mobility grouping on.  Total pages: 2059784
  278. [    1.015319] Kernel command line: storagemedia=scsi androidboot.storagemedia=scsi androidboot.mode=normal  androidboot.verifiedbootstate=orange rw rootwait earlycon=uart8250,mmio32,0x2ad40000 console=ttyFIQ0 root=PARTUUID=614e0000-0000 rcupdate.rcu_expedited=1 rcu_nocbs=all androidboot.fwver=ddr-v1.03-81dd75088a,spl-v1.03,bl31-v1.05,bl32-v1.02,uboot-3d9aaf2591-05/15/2024
  279. [    1.018611] Unknown kernel command line parameters "storagemedia=scsi", will be passed to user space.
  280. [    1.020435] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
  281. [    1.021660] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
  282. [    1.022402] mem auto-init: stack:off, heap alloc:off, heap free:off
  283. [    1.022993] software IO TLB: area num 8.
  284. [    1.038739] software IO TLB: mapped [mem 0x00000000f7d24000-0x00000000fbd24000] (64MB)
  285. [    1.120357] Memory: 8083140K/8370176K available (21184K kernel code, 3632K rwdata, 7500K rodata, 7616K init, 699K bss, 270652K reserved, 16384K cma-reserved)
  286. [    1.121784] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
  287. [    1.122429] ftrace: allocating 63799 entries in 250 pages
  288. [    1.206006] ftrace: allocated 250 pages with 6 groups
  289. [    1.206574] trace event string verifier disabled
  290. [    1.207183] rcu: Hierarchical RCU implementation.
  291. [    1.207628] rcu:     RCU event tracing is enabled.
  292. [    1.208055]  All grace periods are expedited (rcu_expedited).
  293. [    1.208595]  Rude variant of Tasks RCU enabled.
  294. [    1.209022] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
  295. [    1.216967] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
  296. [    1.220317] Root IRQ handler: gic_handle_irq
  297. [    1.220739] GIC: Using split EOI/Deactivate mode
  298. [    1.222461] rcu:     Offload RCU callbacks from CPUs: 0-7.
  299. [    1.222979] rcu: srcu_init: Setting srcu_struct sizes based on contention.
  300. [    1.249291] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
  301. [    1.249873] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
  302. [    1.250866] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
  303. [    1.253300] Console: colour dummy device 80x25
  304. [    1.253750] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
  305. [    1.254694] pid_max: default: 32768 minimum: 301
  306. [    1.255245] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
  307. [    1.255958] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
  308. [    1.257424] cacheinfo: Unable to detect cache hierarchy for CPU 0
  309. [    1.258346] cblist_init_generic: Setting adjustable number of callback queues.
  310. [    1.259009] cblist_init_generic: Setting shift to 3 and lim to 1.
  311. [    1.259669] rcu: Hierarchical SRCU implementation.
  312. [    1.260108] rcu:     Max phase no-delay instances is 1000.
  313. [    1.262900] EFI services will not be available.
  314. [    1.263640] smp: Bringing up secondary CPUs ...
  315. I/TC: Secondary CPU 1 initializing
  316. I/TC: Secondary CPU 1 switching to normal world boot
  317. I/TC: Secondary CPU 2 initializing
  318. I/TC: Secondary CPU 2 switching to normal world boot
  319. I/TC: Secondary CPU 3 initializing
  320. I/TC: Secondary CPU 3 switching to normal world boot
  321. I/TC: Secondary CPU 4 initializing
  322. I/TC: Secondary CPU 4 switching to normal world boot
  323. I/TC: Secondary CPU 5 initializing
  324. I/TC: Secondary CPU 5 switching to normal world boot
  325. I/TC: Secondary CPU 6 initializing
  326. I/TC: Secondary CPU 6 switching to normal world boot
  327. I/TC: Secondary CPU 7 initializing
  328. I/TC: Secondary CPU 7 switching to normal world boot
  329. [    1.265142] Detected VIPT I-cache on CPU1
  330. [    1.265198] cacheinfo: Unable to detect cache hierarchy for CPU 1
  331. [    1.265232] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
  332. [    1.266310] Detected VIPT I-cache on CPU2
  333. [    1.266355] cacheinfo: Unable to detect cache hierarchy for CPU 2
  334. [    1.266374] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
  335. [    1.267429] Detected VIPT I-cache on CPU3
  336. [    1.267470] cacheinfo: Unable to detect cache hierarchy for CPU 3
  337. [    1.267486] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
  338. [    1.268571] CPU features: detected: Spectre-BHB
  339. [    1.268577] CPU features: detected: ARM erratum 1742098
  340. [    1.268579] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
  341. [    1.268582] Detected PIPT I-cache on CPU4
  342. [    1.268626] cacheinfo: Unable to detect cache hierarchy for CPU 4
  343. [    1.268645] CPU4: Booted secondary processor 0x0000000100 [0x411fd080]
  344. [    1.269695] Detected PIPT I-cache on CPU5
  345. [    1.269731] cacheinfo: Unable to detect cache hierarchy for CPU 5
  346. [    1.269742] CPU5: Booted secondary processor 0x0000000101 [0x411fd080]
  347. [    1.270779] Detected PIPT I-cache on CPU6
  348. [    1.270815] cacheinfo: Unable to detect cache hierarchy for CPU 6
  349. [    1.270827] CPU6: Booted secondary processor 0x0000000102 [0x411fd080]
  350. [    1.271873] Detected PIPT I-cache on CPU7
  351. [    1.271909] cacheinfo: Unable to detect cache hierarchy for CPU 7
  352. [    1.271921] CPU7: Booted secondary processor 0x0000000103 [0x411fd080]
  353. [    1.271974] smp: Brought up 1 node, 8 CPUs
  354. [    1.284505] SMP: Total of 8 processors activated.
  355. [    1.284937] CPU features: detected: 32-bit EL0 Support
  356. [    1.285408] CPU features: detected: CRC32 instructions
  357. [    1.285960] CPU: All CPU(s) started at EL2
  358. [    1.286337] alternatives: applying system-wide alternatives
  359. [    1.288777] devtmpfs: initialized
  360. [    1.304715] Registered cp15_barrier emulation handler
  361. [    1.305177] Registered setend emulation handler
  362. [    1.305666] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
  363. [    1.306540] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
  364. [    1.307401] pinctrl core: initialized pinctrl subsystem
  365. [    1.308147] DMI not present or invalid.
  366. [    1.308635] NET: Registered PF_NETLINK/PF_ROUTE protocol family
  367. [    1.309942] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
  368. [    1.310815] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
  369. [    1.311752] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
  370. [    1.315398] Registered FIQ tty driver
  371. [    1.315899] thermal_sys: Registered thermal governor 'fair_share'
  372. [    1.315902] thermal_sys: Registered thermal governor 'step_wise'
  373. [    1.316445] thermal_sys: Registered thermal governor 'user_space'
  374. [    1.316980] thermal_sys: Registered thermal governor 'power_allocator'
  375. [    1.317550] cpuidle: using governor menu
  376. [    1.318621] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
  377. [    1.319330] ASID allocator initialised with 65536 entries
  378. [    1.321903] ramoops: dmesg-0 0x18000@0x0000000040110000
  379. [    1.322375] ramoops: dmesg-1 0x18000@0x0000000040128000
  380. [    1.322853] ramoops: console 0x80000@0x0000000040140000
  381. [    1.323324] ramoops: pmsg    0x30000@0x00000000401c0000
  382. [    1.324022] printk: console [ramoops-1] enabled
  383. [    1.324428] pstore: Registered ramoops as persistent store backend
  384. [    1.324978] ramoops: using 0xe0000@0x40110000, ecc: 0
  385. [    1.327194] platform mipi0-csi2: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@1/endpoint@0
  386. [    1.328128] platform mipi3-csi2: Fixed dependency cycle(s) with /csi2-dphy3/ports/port@1/endpoint@0
  387. [    1.329232] platform rkcif-mipi-lvds: Fixed dependency cycle(s) with /mipi0-csi2/ports/port@1/endpoint@0
  388. [    1.330226] platform rkcif-mipi-lvds3: Fixed dependency cycle(s) with /mipi3-csi2/ports/port@1/endpoint@0
  389. [    1.331220] platform rkisp-vir0: Fixed dependency cycle(s) with /rkcif-mipi-lvds-sditf/port/endpoint
  390. [    1.332115] platform rkisp-vir1: Fixed dependency cycle(s) with /rkcif-mipi-lvds3-sditf/port/endpoint
  391. [    1.342321] platform 27da0000.hdmi: Fixed dependency cycle(s) with /vop@27d00000/ports/port@0/endpoint@2
  392. [    1.363364] rockchip-gpio 27320000.gpio: probed /pinctrl/gpio@27320000
  393. [    1.364236] rockchip-gpio 2ae10000.gpio: probed /pinctrl/gpio@2ae10000
  394. [    1.365092] rockchip-gpio 2ae20000.gpio: probed /pinctrl/gpio@2ae20000
  395. [    1.365959] rockchip-gpio 2ae30000.gpio: probed /pinctrl/gpio@2ae30000
  396. [    1.366834] rockchip-gpio 2ae40000.gpio: probed /pinctrl/gpio@2ae40000
  397. [    1.367521] rockchip-pinctrl pinctrl: probed pinctrl
  398. [    1.378727] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ fiq not found
  399. [    1.379335] fiq_debugger fiq_debugger.0: error -ENXIO: IRQ wakeup not found
  400. [    1.379957] fiq_debugger_probe: could not install nmi irq handler
  401. [[    1.380563] printk: console [ttyFIQ0] enabled
  402.     1.380563] printk: console [ttyFIQ0] enabled
  403. [    1.381332] printk: bootconsole [uart8250] disabled
  404. [    1.381332] printk: bootconsole [uart8250] disabled
  405. [    1.381843] Registered fiq debugger ttyFIQ0
  406. [    1.383751] iommu: Default domain type: Translated
  407. [    1.383764] iommu: DMA domain TLB invalidation policy: strict mode
  408. [    1.383925] SCSI subsystem initialized
  409. [    1.384021] usbcore: registered new interface driver usbfs
  410. [    1.384041] usbcore: registered new interface driver hub
  411. [    1.384061] usbcore: registered new device driver usb
  412. [    1.384126] mc: Linux media interface: v0.10
  413. [    1.384148] videodev: Linux video capture interface: v2.00
  414. [    1.384187] pps_core: LinuxPPS API ver. 1 registered
  415. [    1.384192] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  416. [    1.384203] PTP clock support registered
  417. [    1.384225] EDAC MC: Ver: 3.0.0
  418. [    1.384692] arm-scmi firmware:scmi: Enabled polling mode TX channel - prot_id:16
  419. [    1.384763] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
  420. [    1.384803] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
  421. [    1.386101] Advanced Linux Sound Architecture Driver Initialized.
  422. [    1.386313] Bluetooth: Core ver 2.22
  423. [    1.386335] NET: Registered PF_BLUETOOTH protocol family
  424. [    1.386341] Bluetooth: HCI device and connection manager initialized
  425. [    1.386349] Bluetooth: HCI socket layer initialized
  426. [    1.386355] Bluetooth: L2CAP socket layer initialized
  427. [    1.386365] Bluetooth: SCO socket layer initialized
  428. [    1.387680] rockchip-cpuinfo cpuinfo: SoC            : 35760000
  429. [    1.387689] rockchip-cpuinfo cpuinfo: Serial         : 5480dffd8ef8467a
  430. [    1.388156] clocksource: Switched to clocksource arch_sys_counter
  431. [    1.392456] NET: Registered PF_INET protocol family
  432. [    1.392627] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
  433. [    1.396190] tcp_listen_portaddr_hash hash table entries: 4096 (order: 4, 65536 bytes, linear)
  434. [    1.396242] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
  435. [    1.396273] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
  436. [    1.396563] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear)
  437. [    1.397623] TCP: Hash tables configured (established 65536 bind 65536)
  438. [    1.397692] UDP hash table entries: 4096 (order: 5, 131072 bytes, linear)
  439. [    1.397809] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes, linear)
  440. [    1.397998] NET: Registered PF_UNIX/PF_LOCAL protocol family
  441. [    1.398198] RPC: Registered named UNIX socket transport module.
  442. [    1.398207] RPC: Registered udp transport module.
  443. [    1.398212] RPC: Registered tcp transport module.
  444. [    1.398217] RPC: Registered tcp NFSv4.1 backchannel transport module.
  445. [    1.398686] PCI: CLS 0 bytes, default 64
  446. [    1.400198] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
  447. [    1.400641] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
  448. [    1.729542] Initialise system trusted keyrings
  449. [    1.729650] workingset: timestamp_bits=62 max_order=21 bucket_order=0
  450. [    1.732003] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  451. [    1.732329] NFS: Registering the id_resolver key type
  452. [    1.732347] Key type id_resolver registered
  453. [    1.732353] Key type id_legacy registered
  454. [    1.732373] ntfs: driver 2.1.32 [Flags: R/O].
  455. [    1.732443] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
  456. [    1.732572] fuse: init (API version 7.37)
  457. [    1.732732] SGI XFS with security attributes, no debug enabled
  458. [    1.760233] NET: Registered PF_ALG protocol family
  459. [    1.760249] Key type asymmetric registered
  460. [    1.760255] Asymmetric key parser 'x509' registered
  461. [    1.760284] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
  462. [    1.760292] io scheduler mq-deadline registered
  463. [    1.760298] io scheduler kyber registered
  464. [    1.761380] rockchip-csi2-dphy-hw 2b030000.csi2-dphy0-hw: csi2 dphy hw probe successfully!
  465. [    1.761486] rockchip-csi2-dphy-hw 2b070000.csi2-dphy1-hw: csi2 dphy hw probe successfully!
  466. [    1.762521] rockchip-usb2phy 2602e000.syscon:usb2-phy@0: error -ENXIO: IRQ index 0 not found
  467. [    1.762610] rockchip-usb2phy 2602e000.syscon:usb2-phy@0: refclk freq 24000000
  468. [    1.763802] rockchip-usb2phy 2602e000.syscon:usb2-phy@2000: error -ENXIO: IRQ index 0 not found
  469. [    1.763891] rockchip-usb2phy 2602e000.syscon:usb2-phy@2000: refclk freq 24000000
  470. [    1.767272] rockchip-hdptx-phy-hdmi 2b000000.hdmiphy: hdptx phy init success
  471. [    1.769950] rk-pcie 2a200000.pcie: invalid prsnt-gpios property in node
  472. [    1.770322] pwm-backlight backlight: supply power not found, using dummy regulator
  473. [    1.770643] iep: Module initialized.
  474. [    1.770679] mpp_service mpp-srv: 4d15cf548848 author: Chandler Chen 2024-07-30 video: rockchip: mpp: rkvdec: add spinlock for mmu fault handle
  475. [    1.770687] mpp_service mpp-srv: probe start
  476. [    1.770762] rk-pcie 2a200000.pcie: max MSI vector is 32
  477. [    1.770808] rk-pcie 2a200000.pcie: host bridge /pcie@2a200000 ranges:
  478. [    1.770834] rk-pcie 2a200000.pcie:      err 0x0020000000..0x00200fffff -> 0x0020000000
  479. [    1.770851] rk-pcie 2a200000.pcie:       IO 0x0020100000..0x00201fffff -> 0x0020100000
  480. [    1.770868] rk-pcie 2a200000.pcie:      MEM 0x0020200000..0x0020ffffff -> 0x0020200000
  481. [    1.770881] rk-pcie 2a200000.pcie:      MEM 0x0900000000..0x097fffffff -> 0x0900000000
  482. [    1.770997] rk-pcie 2a200000.pcie: iATU unroll: enabled
  483. [    1.771007] rk-pcie 2a200000.pcie: iATU regions: 8 ob, 8 ib, align 64K, limit 8G
  484. [    1.772677] mpp_rkvenc2 rkvenc-ccu: probing start
  485. [    1.772688] mpp_rkvenc2 rkvenc-ccu: probing finish
  486. [    1.773075] mpp_service mpp-srv: probe success
  487. [    1.781935] dma-pl330 2ab90000.dma-controller: Loaded driver for PL330 DMAC-241330
  488. [    1.781948] dma-pl330 2ab90000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
  489. [    1.782674] dma-pl330 2abb0000.dma-controller: Loaded driver for PL330 DMAC-241330
  490. [    1.782682] dma-pl330 2abb0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
  491. [    1.783399] dma-pl330 2abd0000.dma-controller: Loaded driver for PL330 DMAC-241330
  492. [    1.783407] dma-pl330 2abd0000.dma-controller:       DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
  493. [    1.784513] rockchip-system-monitor rockchip-system-monitor: system monitor probe
  494. [    1.784829] arm-scmi firmware:scmi: Failed. SCMI protocol 22 not active.
  495. [    1.784920] Serial: 8250/16550 driver, 15 ports, IRQ sharing disabled
  496. [    1.785576] 2ada0000.serial: ttyS7 at MMIO 0x2ada0000 (irq = 44, base_baud = 11718) is a 16550A
  497. [    1.796513] cacheinfo: Unable to detect cache hierarchy for CPU 0
  498. [    1.796827] brd: module loaded
  499. [    1.799001] loop: module loaded
  500. [    1.799152] zram: Added device: zram0
  501. [    1.799290] lkdtm: No crash points registered, enable through debugfs
  502. [    1.801224] CAN device driver interface
  503. [    1.802004] rk_gmac-dwmac 2a220000.ethernet: IRQ eth_lpi not found
  504. [    1.802147] rk_gmac-dwmac 2a220000.ethernet: supply phy not found, using dummy regulator
  505. [    1.802204] rk_gmac-dwmac 2a220000.ethernet: clock input or output? (output).
  506. [    1.802211] rk_gmac-dwmac 2a220000.ethernet: TX delay(0x21).
  507. [    1.802218] rk_gmac-dwmac 2a220000.ethernet: Can not read property: rx_delay.
  508. [    1.802223] rk_gmac-dwmac 2a220000.ethernet: set rx_delay to 0xffffffff
  509. [    1.802281] rk_gmac-dwmac 2a220000.ethernet: integrated PHY? (no).
  510. [    1.802291] rk_gmac-dwmac 2a220000.ethernet: cannot get clock mac_clk_rx
  511. [    1.802297] rk_gmac-dwmac 2a220000.ethernet: cannot get clock mac_clk_tx
  512. [    1.802312] rk_gmac-dwmac 2a220000.ethernet: cannot get clock clk_mac_speed
  513. [    1.802544] rk_gmac-dwmac 2a220000.ethernet: init for RGMII_RXID
  514. [    1.802622] rk_gmac-dwmac 2a220000.ethernet: User ID: 0x30, Synopsys ID: 0x51
  515. [    1.802632] rk_gmac-dwmac 2a220000.ethernet:         DWMAC4/5
  516. [    1.802639] rk_gmac-dwmac 2a220000.ethernet: DMA HW capability register supported
  517. [    1.802645] rk_gmac-dwmac 2a220000.ethernet: RX Checksum Offload Engine supported
  518. [    1.802650] rk_gmac-dwmac 2a220000.ethernet: TX Checksum insertion supported
  519. [    1.802655] rk_gmac-dwmac 2a220000.ethernet: Wake-Up On Lan supported
  520. [    1.802684] rk_gmac-dwmac 2a220000.ethernet: TSO supported
  521. [    1.802690] rk_gmac-dwmac 2a220000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  522. [    1.802696] rk_gmac-dwmac 2a220000.ethernet: Enabled L3L4 Flow TC (entries=2)
  523. [    1.802701] rk_gmac-dwmac 2a220000.ethernet: Enabled RFS Flow TC (entries=10)
  524. [    1.802707] rk_gmac-dwmac 2a220000.ethernet: TSO feature enabled
  525. [    1.802713] rk_gmac-dwmac 2a220000.ethernet: Using 40/40 bits DMA host/device width
  526. [    1.939275] rk_gmac-dwmac 2a230000.ethernet: IRQ eth_lpi not found
  527. [    1.939419] rk_gmac-dwmac 2a230000.ethernet: supply phy not found, using dummy regulator
  528. [    1.939477] rk_gmac-dwmac 2a230000.ethernet: clock input or output? (output).
  529. [    1.939484] rk_gmac-dwmac 2a230000.ethernet: TX delay(0x22).
  530. [    1.939491] rk_gmac-dwmac 2a230000.ethernet: Can not read property: rx_delay.
  531. [    1.939496] rk_gmac-dwmac 2a230000.ethernet: set rx_delay to 0xffffffff
  532. [    1.939511] rk_gmac-dwmac 2a230000.ethernet: integrated PHY? (no).
  533. [    1.939519] rk_gmac-dwmac 2a230000.ethernet: cannot get clock mac_clk_rx
  534. [    1.939525] rk_gmac-dwmac 2a230000.ethernet: cannot get clock mac_clk_tx
  535. [    1.939538] rk_gmac-dwmac 2a230000.ethernet: cannot get clock clk_mac_speed
  536. [    1.939757] rk_gmac-dwmac 2a230000.ethernet: init for RGMII_RXID
  537. [    1.939835] rk_gmac-dwmac 2a230000.ethernet: User ID: 0x30, Synopsys ID: 0x51
  538. [    1.939843] rk_gmac-dwmac 2a230000.ethernet:         DWMAC4/5
  539. [    1.939851] rk_gmac-dwmac 2a230000.ethernet: DMA HW capability register supported
  540. [    1.939856] rk_gmac-dwmac 2a230000.ethernet: RX Checksum Offload Engine supported
  541. [    1.939861] rk_gmac-dwmac 2a230000.ethernet: TX Checksum insertion supported
  542. [    1.939866] rk_gmac-dwmac 2a230000.ethernet: Wake-Up On Lan supported
  543. [    1.939894] rk_gmac-dwmac 2a230000.ethernet: TSO supported
  544. [    1.939900] rk_gmac-dwmac 2a230000.ethernet: Enable RX Mitigation via HW Watchdog Timer
  545. [    1.939906] rk_gmac-dwmac 2a230000.ethernet: Enabled L3L4 Flow TC (entries=2)
  546. [    1.939912] rk_gmac-dwmac 2a230000.ethernet: Enabled RFS Flow TC (entries=10)
  547. [    1.939917] rk_gmac-dwmac 2a230000.ethernet: TSO feature enabled
  548. [    1.939923] rk_gmac-dwmac 2a230000.ethernet: Using 40/40 bits DMA host/device width
  549. [    1.977273] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  550. [    2.004162] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  551. [    2.032162] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  552. [    2.060161] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  553. [    2.075166] usbcore: registered new interface driver rtl8150
  554. [    2.075183] usbcore: registered new device driver r8152-cfgselector
  555. [    2.075205] usbcore: registered new interface driver r8152
  556. [    2.080093] rockchip-usb2phy 2602e000.syscon:usb2-phy@2000: Requested PHY is disabled
  557. [    2.081869] rockchip-usb2phy 2602e000.syscon:usb2-phy@2000: Requested PHY is disabled
  558. [    2.081888] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  559. [    2.081958] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
  560. [    2.082027] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000800002010010
  561. [    2.082055] xhci-hcd xhci-hcd.0.auto: irq 62, io mem 0x23400000
  562. [    2.082123] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
  563. [    2.082191] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
  564. [    2.082201] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
  565. [    2.082260] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
  566. [    2.082268] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  567. [    2.082274] usb usb1: Product: xHCI Host Controller
  568. [    2.082279] usb usb1: Manufacturer: Linux 6.1.75 xhci-hcd
  569. [    2.082285] usb usb1: SerialNumber: xhci-hcd.0.auto
  570. [    2.082468] hub 1-0:1.0: USB hub found
  571. [    2.082484] hub 1-0:1.0: 1 port detected
  572. [    2.082625] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
  573. [    2.082665] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
  574. [    2.082673] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  575. [    2.082679] usb usb2: Product: xHCI Host Controller
  576. [    2.082684] usb usb2: Manufacturer: Linux 6.1.75 xhci-hcd
  577. [    2.082690] usb usb2: SerialNumber: xhci-hcd.0.auto
  578. [    2.082853] hub 2-0:1.0: USB hub found
  579. [    2.082869] hub 2-0:1.0: 1 port detected
  580. [    2.083026] usbcore: registered new interface driver cdc_acm
  581. [    2.083032] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
  582. [    2.083105] usbcore: registered new interface driver uas
  583. [    2.083132] usbcore: registered new interface driver usb-storage
  584. [    2.083165] usbcore: registered new interface driver usbserial_generic
  585. [    2.083176] usbserial: USB Serial support registered for generic
  586. [    2.083193] usbcore: registered new interface driver cp210x
  587. [    2.083203] usbserial: USB Serial support registered for cp210x
  588. [    2.083221] usbcore: registered new interface driver ftdi_sio
  589. [    2.083233] usbserial: USB Serial support registered for FTDI USB Serial Device
  590. [    2.083261] usbcore: registered new interface driver keyspan
  591. [    2.083273] usbserial: USB Serial support registered for Keyspan - (without firmware)
  592. [    2.083282] usbserial: USB Serial support registered for Keyspan 1 port adapter
  593. [    2.083292] usbserial: USB Serial support registered for Keyspan 2 port adapter
  594. [    2.083301] usbserial: USB Serial support registered for Keyspan 4 port adapter
  595. [    2.083317] usbcore: registered new interface driver option
  596. [    2.083327] usbserial: USB Serial support registered for GSM modem (1-port)
  597. [    2.083362] usbcore: registered new interface driver oti6858
  598. [    2.083372] usbserial: USB Serial support registered for oti6858
  599. [    2.083387] usbcore: registered new interface driver pl2303
  600. [    2.083397] usbserial: USB Serial support registered for pl2303
  601. [    2.083418] usbcore: registered new interface driver qcserial
  602. [    2.083427] usbserial: USB Serial support registered for Qualcomm USB modem
  603. [    2.083445] usbcore: registered new interface driver sierra
  604. [    2.083455] usbserial: USB Serial support registered for Sierra USB modem
  605. [    2.083858] usbcore: registered new interface driver usbtouchscreen
  606. [    2.084155] i2c_dev: i2c /dev entries driver
  607. [    2.085500] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs1_pwrdn
  608. [    2.085516] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs3_null
  609. [    2.085528] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs2_null
  610. [    2.085539] i2c 1-0023: Fixed dependency cycle(s) with /i2c@2ac40000/pmic@23/pinctrl_rk806/rk806_dvs1_null
  611. [    2.087275] rk806 1-0023: chip id: RK806,ver:0xa, 0x5
  612. [    2.088164] rk806 1-0023: ON: 0x40 OFF:0x0
  613. [    2.088166] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  614. [    2.098381] input: rk805 pwrkey as /devices/platform/2ac40000.i2c/i2c-1/1-0023/rk805-pwrkey.2.auto/input/input0
  615. [    2.116161] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  616. [    2.144163] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  617. [    2.156006] rk806 1-0023: no sleep-setting state
  618. [    2.156019] rk806 1-0023: no reset-setting pinctrl state
  619. [    2.156025] rk806 1-0023: no dvs-setting pinctrl state
  620. [    2.165368] i2c 6-001a: Fixed dependency cycle(s) with /csi2-dphy3/ports/port@0/endpoint@1
  621. [    2.165611] i2c 6-0036: Fixed dependency cycle(s) with /csi2-dphy3/ports/port@0/endpoint@2
  622. [    2.168841] rtc-hym8563 7-0051: rtc information is invalid
  623. [    2.172164] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  624. [    2.177200] rtc-hym8563 7-0051: registered as rtc0
  625. [    2.178199] rtc-hym8563 7-0051: setting system clock to 2021-01-01T12:00:00 UTC (1609502400)
  626. [    2.178761] i2c 9-001a: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@1
  627. [    2.178984] i2c 9-0036: Fixed dependency cycle(s) with /csi2-dcphy0/ports/port@0/endpoint@2
  628. [    2.179252] otp_eeprom 6-0050: driver version: 00.01.03
  629. [    2.179269] otp_eeprom 6-0050: probing successful
  630. [    2.179302] otp_eeprom 9-0050: driver version: 00.01.03
  631. [    2.179313] otp_eeprom 9-0050: probing successful
  632. [    2.179778] rkcifhw 27c10000.rkcif: Adding to iommu group 9
  633. [    2.180102] rkcifhw 27c10000.rkcif: No reserved memory region assign to CIF
  634. [    2.180226] rkcif rkcif-mipi-lvds: Adding to iommu group 9
  635. [    2.180242] rkcif rkcif-mipi-lvds: rkcif driver version: v00.02.00
  636. [    2.180316] rkcif rkcif-mipi-lvds: attach to cif hw node
  637. [    2.180321] rkcif rkcif-mipi-lvds: rkcif wait line 0
  638. [    2.180327] rkcif rkcif-mipi-lvds: rkcif fastboot reserve bufs num 3
  639. [    2.180335] : terminal subdev does not exist
  640. [    2.180341] : terminal subdev does not exist
  641. [    2.180347] : terminal subdev does not exist
  642. [    2.180352] : terminal subdev does not exist
  643. [    2.180358] : get_remote_sensor: video pad[0] is null
  644. [    2.180363] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  645. [    2.180368] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  646. [    2.180375] : get_remote_sensor: video pad[0] is null
  647. [    2.180379] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  648. [    2.180384] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  649. [    2.180390] : get_remote_sensor: video pad[0] is null
  650. [    2.180394] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  651. [    2.180399] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  652. [    2.180405] : get_remote_sensor: video pad[0] is null
  653. [    2.180409] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  654. [    2.180414] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  655. [    2.181030] rkcif rkcif-mipi-lvds: No memory-region-thunderboot specified
  656. [    2.181144] rkcif rkcif-mipi-lvds3: Adding to iommu group 9
  657. [    2.181160] rkcif rkcif-mipi-lvds3: rkcif driver version: v00.02.00
  658. [    2.181206] rkcif rkcif-mipi-lvds3: attach to cif hw node
  659. [    2.181212] rkcif rkcif-mipi-lvds3: rkcif wait line 0
  660. [    2.181217] rkcif rkcif-mipi-lvds3: rkcif fastboot reserve bufs num 3
  661. [    2.181224] : terminal subdev does not exist
  662. [    2.181231] : terminal subdev does not exist
  663. [    2.181236] : terminal subdev does not exist
  664. [    2.181242] : terminal subdev does not exist
  665. [    2.181247] : get_remote_sensor: video pad[0] is null
  666. [    2.181252] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  667. [    2.181257] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  668. [    2.181264] : get_remote_sensor: video pad[0] is null
  669. [    2.181268] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  670. [    2.181273] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  671. [    2.181278] : get_remote_sensor: video pad[0] is null
  672. [    2.181282] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  673. [    2.181287] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  674. [    2.181293] : get_remote_sensor: video pad[0] is null
  675. [    2.181297] : rkcif_update_sensor_info: stream[0] get remote sensor_sd failed!
  676. [    2.181302] : rkcif_scale_set_fmt: req(40, 30) src out(0, 0)
  677. [    2.181901] rkcif rkcif-mipi-lvds3: No memory-region-thunderboot specified
  678. [    2.182723] rockchip-mipi-csi2-hw 27c80000.mipi0-csi2-hw: enter mipi csi2 hw probe!
  679. [    2.182837] rockchip-mipi-csi2-hw 27c80000.mipi0-csi2-hw: probe success, v4l2_dev:mipi0-csi2-hw!
  680. [    2.182872] rockchip-mipi-csi2-hw 27c90000.mipi1-csi2-hw: enter mipi csi2 hw probe!
  681. [    2.182941] rockchip-mipi-csi2-hw 27c90000.mipi1-csi2-hw: probe success, v4l2_dev:mipi1-csi2-hw!
  682. [    2.182972] rockchip-mipi-csi2-hw 27ca0000.mipi2-csi2-hw: enter mipi csi2 hw probe!
  683. [    2.183042] rockchip-mipi-csi2-hw 27ca0000.mipi2-csi2-hw: probe success, v4l2_dev:mipi2-csi2-hw!
  684. [    2.183074] rockchip-mipi-csi2-hw 27cb0000.mipi3-csi2-hw: enter mipi csi2 hw probe!
  685. [    2.183139] rockchip-mipi-csi2-hw 27cb0000.mipi3-csi2-hw: probe success, v4l2_dev:mipi3-csi2-hw!
  686. [    2.183170] rockchip-mipi-csi2-hw 27cc0000.mipi4-csi2-hw: enter mipi csi2 hw probe!
  687. [    2.183234] rockchip-mipi-csi2-hw 27cc0000.mipi4-csi2-hw: probe success, v4l2_dev:mipi4-csi2-hw!
  688. [    2.183581] rockchip-mipi-csi2 mipi0-csi2: attach to csi2 hw node
  689. [    2.183605] rkcif rkcif-mipi-lvds: Entity type for entity rockchip-mipi-csi2 was not initialized!
  690. [    2.183613] rockchip-mipi-csi2: Async registered subdev
  691. [    2.183619] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds!
  692. [    2.183814] rockchip-mipi-csi2 mipi3-csi2: attach to csi2 hw node
  693. [    2.183834] rkcif rkcif-mipi-lvds3: Entity type for entity rockchip-mipi-csi2 was not initialized!
  694. [    2.183841] rockchip-mipi-csi2: Async registered subdev
  695. [    2.183846] rockchip-mipi-csi2: probe success, v4l2_dev:rkcif-mipi-lvds3!
  696. [    2.184567] rkisp_hw 27c00000.isp: Adding to iommu group 8
  697. [    2.184708] rkisp_hw 27c00000.isp: is_thunderboot: 0
  698. [    2.184716] rkisp_hw 27c00000.isp: Missing rockchip,grf property
  699. [    2.184735] rkisp_hw 27c00000.isp: max input:0x0@0fps
  700. [    2.184850] rkisp_hw 27c00000.isp: no find phandle sram
  701. [    2.185078] rkisp rkisp-vir0: rkisp driver version: v02.06.00
  702. [    2.185156] rkisp rkisp-vir0: No memory-region-thunderboot specified
  703. [    2.185223] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
  704. [    2.185801] rkisp rkisp-vir1: rkisp driver version: v02.06.00
  705. [    2.185861] rkisp rkisp-vir1: No memory-region-thunderboot specified
  706. [    2.185914] rkisp rkisp-vir1: Entity type for entity rkisp-isp-subdev was not initialized!
  707. [    2.187452] usbcore: registered new interface driver uvcvideo
  708. [    2.188437] Bluetooth: HCI UART driver ver 2.3
  709. [    2.188447] Bluetooth: HCI UART protocol H4 registered
  710. [    2.188452] Bluetooth: HCI UART protocol ATH3K registered
  711. [    2.188477] usbcore: registered new interface driver bfusb
  712. [    2.188499] usbcore: registered new interface driver btusb
  713. [    2.189559] cpu cpu0: bin=0
  714. [    2.189776] cpu cpu0: leakage=4
  715. [    2.190987] cpu cpu4: bin=0
  716. [    2.191192] cpu cpu4: leakage=6
  717. [    2.192636] cpu cpu0: avs=0
  718. [    2.193448] cpu cpu4: avs=0
  719. [    2.193528] cpu cpu0: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  720. [    2.194583] cpu cpu0: EM: created perf domain
  721. [    2.195008] cpu cpu4: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  722. [    2.196105] cpu cpu4: EM: created perf domain
  723. [    2.197632] sdhci: Secure Digital Host Controller Interface driver
  724. [    2.197643] sdhci: Copyright(c) Pierre Ossman
  725. [    2.197649] Synopsys Designware Multimedia Card Interface Driver
  726. [    2.198150] sdhci-pltfm: SDHCI platform and OF driver helper
  727. [    2.198779] dwmmc_rockchip 2a320000.mmc: No normal pinctrl state
  728. [    2.198793] dwmmc_rockchip 2a320000.mmc: No idle pinctrl state
  729. [    2.198957] dwmmc_rockchip 2a320000.mmc: IDMAC supports 32-bit address mode.
  730. [    2.198989] dwmmc_rockchip 2a320000.mmc: Using internal DMA controller.
  731. [    2.199000] dwmmc_rockchip 2a320000.mmc: Version ID is 270a
  732. [    2.199032] dwmmc_rockchip 2a320000.mmc: DW MMC controller at irq 87,32 bit host data width,256 deep fifo
  733. [    2.199102] dwmmc_rockchip 2a310000.mmc: No normal pinctrl state
  734. [    2.199121] dwmmc_rockchip 2a310000.mmc: No idle pinctrl state
  735. [    2.199296] dwmmc_rockchip 2a320000.mmc: allocated mmc-pwrseq
  736. [    2.199307] mmc_host mmc0: card is non-removable.
  737. [    2.199441] dwmmc_rockchip 2a310000.mmc: IDMAC supports 32-bit address mode.
  738. [    2.199480] dwmmc_rockchip 2a310000.mmc: Using internal DMA controller.
  739. [    2.199492] dwmmc_rockchip 2a310000.mmc: Version ID is 270a
  740. [    2.199535] dwmmc_rockchip 2a310000.mmc: DW MMC controller at irq 88,32 bit host data width,256 deep fifo
  741. [    2.199960] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vdd-hba-supply regulator, assuming enabled
  742. [    2.199971] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vcc-supply regulator, assuming enabled
  743. [    2.199976] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vccq-supply regulator, assuming enabled
  744. [    2.199981] ufshcd-rockchip 2a2d0000.ufs: ufshcd_populate_vreg: Unable to find vccq2-supply regulator, assuming enabled
  745. [    2.200071] mmc2: CQHCI version 5.10
  746. [    2.200202] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  747. [    2.200394] scsi host0: ufshcd
  748. [    2.202117] arm-scmi firmware:scmi: Failed. SCMI protocol 17 not active.
  749. [    2.202148] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
  750. [    2.202514] cryptodev: driver 1.12 loaded.
  751. [    2.202535] hid: raw HID events driver (C) Jiri Kosina
  752. [    2.202632] usbcore: registered new interface driver usbhid
  753. [    2.202637] usbhid: USB HID core driver
  754. [    2.205076] optee: probing for conduit method.
  755. [    2.205090] optee: revision 3.13 (b90c1680)
  756. [    2.205168] optee: dynamic shared memory is enabled
  757. [    2.205251] optee: initialized driver
  758. [    2.205534] usbcore: registered new interface driver snd-usb-audio
  759. [    2.208685] Initializing XFRM netlink socket
  760. [    2.208850] NET: Registered PF_INET6 protocol family
  761. [    2.209386] Segment Routing with IPv6
  762. [    2.209401] In-situ OAM (IOAM) with IPv6
  763. [    2.209434] NET: Registered PF_PACKET protocol family
  764. [    2.209443] NET: Registered PF_KEY protocol family
  765. [    2.209451] can: controller area network core
  766. [    2.209471] NET: Registered PF_CAN protocol family
  767. [    2.209477] can: raw protocol
  768. [    2.209483] can: broadcast manager protocol
  769. [    2.209489] can: netlink gateway - max_hops=1
  770. [    2.209622] Bluetooth: RFCOMM socket layer initialized
  771. [    2.209639] Bluetooth: RFCOMM ver 1.11
  772. [    2.209647] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
  773. [    2.209654] Bluetooth: HIDP socket layer initialized
  774. [    2.209677] [BT_RFKILL]: Enter rfkill_rk_init
  775. [    2.209682] [WLAN_RFKILL]: Enter rfkill_wlan_init
  776. [    2.210118] [WLAN_RFKILL]: Enter rfkill_wlan_probe
  777. [    2.210142] [WLAN_RFKILL]: can't find rockchip,grf property
  778. [    2.210147] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = ap6275p
  779. [    2.210152] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
  780. [    2.210157] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
  781. [    2.210175] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 8, flags = 0.
  782. [    2.210183] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
  783. [    2.210187] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
  784. [    2.210192] [WLAN_RFKILL]: rfkill_set_wifi_bt_power: 1
  785. [    2.210197] [WLAN_RFKILL]: Exit rfkill_wlan_probe
  786. [    2.210817] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 50.
  787. [    2.210838] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 81.
  788. [    2.210847] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 86.
  789. [    2.210855] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 9.
  790. [    2.210862] [BT_RFKILL]: bluetooth_platdata_parse_dt: clk_get failed!!!.
  791. [    2.210889] [BT_RFKILL]: Request irq for bt wakeup host
  792. [    2.211107] [BT_RFKILL]: ** disable irq
  793. [    2.211157] [BT_RFKILL]: bt_default device registered.
  794. [    2.211211] input: bt-powerkey as /devices/platform/wireless-bluetooth/input/input1
  795. [    2.211325] Key type dns_resolver registered
  796. [    2.211869] imx415 6-001a: driver version: 00.01.08
  797. [    2.211884] imx415 6-001a:  Get hdr mode failed! no hdr default
  798. [    2.211895] imx415 6-001a: detect imx415 lane 4
  799. [    2.211927] imx415 6-001a: could not get default pinstate
  800. [    2.211932] imx415 6-001a: could not get sleep pinstate
  801. [    2.211955] imx415 6-001a: supply dvdd not found, using dummy regulator
  802. [    2.212030] imx415 6-001a: supply dovdd not found, using dummy regulator
  803. [    2.212057] imx415 6-001a: supply avdd not found, using dummy regulator
  804. [    2.212374] mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  805. [    2.228170] rk-pcie 2a200000.pcie: PCIe Linking... LTSSM is 0x3
  806. [    2.228973] mmc2: SDHCI controller on 2a330000.mmc [2a330000.mmc] using ADMA 64-bit
  807. [    2.249893] scsi 0:0:0:49488: Well-known LUN    SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  808. [    2.250965] scsi 0:0:0:49476: Well-known LUN    SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  809. [    2.251894] scsi 0:0:0:49456: Well-known LUN    SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  810. [    2.253355] scsi 0:0:0:0: Direct-Access     SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  811. [    2.254388] scsi 0:0:0:1: Direct-Access     SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  812. [    2.255143] scsi 0:0:0:2: Direct-Access     SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  813. [    2.255905] scsi 0:0:0:3: Direct-Access     SAMSUNG  KLUDG2R1DE-B0F1  0100 PQ: 0 ANSI: 6
  814. [    2.257090] sd 0:0:0:0: [sda] 31234048 4096-byte logical blocks: (128 GB/119 GiB)
  815. [    2.257162] sd 0:0:0:0: [sda] Write Protect is off
  816. [    2.257287] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
  817. [    2.257301] sd 0:0:0:0: [sda] Preferred minimum I/O size 524288 bytes
  818. [    2.257310] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes
  819. [    2.257379] sd 0:0:0:1: [sdb] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
  820. [    2.257497] sd 0:0:0:1: [sdb] Write Protect is off
  821. [    2.257641] sd 0:0:0:1: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
  822. [    2.257654] sd 0:0:0:1: [sdb] Preferred minimum I/O size 524288 bytes
  823. [    2.257663] sd 0:0:0:1: [sdb] Optimal transfer size 524288 bytes
  824. [    2.258070] sd 0:0:0:2: [sdc] 1024 4096-byte logical blocks: (4.19 MB/4.00 MiB)
  825. [    2.258197] sd 0:0:0:2: [sdc] Write Protect is off
  826. [    2.258453] sd 0:0:0:2: [sdc] Write cache: enabled, read cache: enabled, supports DPO and FUA
  827. [    2.258465] sd 0:0:0:2: [sdc] Preferred minimum I/O size 524288 bytes
  828. [    2.258472] sd 0:0:0:2: [sdc] Optimal transfer size 524288 bytes
  829. [    2.259178] sd 0:0:0:1: [sdb] Attached SCSI disk
  830. [    2.259340] sd 0:0:0:3: [sdd] 2048 4096-byte logical blocks: (8.39 MB/8.00 MiB)
  831. [    2.259571] sd 0:0:0:3: [sdd] Write Protect is off
  832. [    2.259825] sd 0:0:0:3: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
  833. [    2.259837] sd 0:0:0:3: [sdd] Preferred minimum I/O size 524288 bytes
  834. [    2.259845] sd 0:0:0:3: [sdd] Optimal transfer size 524288 bytes
  835. [    2.260077] sd 0:0:0:2: [sdc] Attached SCSI disk
  836. [    2.260254]  sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
  837. [    2.260828] sd 0:0:0:3: [sdd] Attached SCSI disk
  838. [    2.261010] sd 0:0:0:0: [sda] Attached SCSI disk
  839. [    2.280480] imx415 6-001a: Unexpected sensor id(000000), ret(-5)
  840. [    2.280928] imx415 9-001a: driver version: 00.01.08
  841. [    2.280943] imx415 9-001a:  Get hdr mode failed! no hdr default
  842. [    2.280956] imx415 9-001a: detect imx415 lane 4
  843. [    2.280990] imx415 9-001a: could not get default pinstate
  844. [    2.280996] imx415 9-001a: could not get sleep pinstate
  845. [    2.281020] imx415 9-001a: supply dvdd not found, using dummy regulator
  846. [    2.281087] imx415 9-001a: supply dovdd not found, using dummy regulator
  847. [    2.281116] imx415 9-001a: supply avdd not found, using dummy regulator
  848. [    2.342148] imx415 9-001a: Unexpected sensor id(000000), ret(-5)
  849. [    2.342689] ov50c40 6-0036: driver version: 00.01.08
  850. [    2.342737] ov50c40 6-0036: failed get spd_id, will not to use spd
  851. [    2.342744] ov50c40 6-0036: could not get default pinstate
  852. [    2.342749] ov50c40 6-0036: could not get sleep pinstate
  853. [    2.342771] ov50c40 6-0036: supply avdd not found, using dummy regulator
  854. [    2.342834] ov50c40 6-0036: supply dovdd not found, using dummy regulator
  855. [    2.342858] ov50c40 6-0036: supply dvdd not found, using dummy regulator
  856. [    2.355234] ov50c40 6-0036: Unexpected sensor id(000000), ret(-5)
  857. [    2.356119] ov50c40 9-0036: driver version: 00.01.08
  858. [    2.356282] ov50c40 9-0036: failed get spd_id, will not to use spd
  859. [    2.356308] ov50c40 9-0036: could not get default pinstate
  860. [    2.356345] ov50c40 9-0036: could not get sleep pinstate
  861. [    2.356436] ov50c40 9-0036: supply avdd not found, using dummy regulator
  862. [    2.356685] ov50c40 9-0036: supply dovdd not found, using dummy regulator
  863. [    2.356766] ov50c40 9-0036: supply dvdd not found, using dummy regulator
  864. [    2.369339] ov50c40 9-0036: Unexpected sensor id(000000), ret(-5)
  865. [    2.372707] Loading compiled-in X.509 certificates
  866. [    2.374957] pstore: Using crash dump compression: deflate
  867. [    2.382430] rga2 27920000.rga: Adding to iommu group 2
  868. [    2.382870] rga2 27920000.rga: probe successfully, irq = 48, hw_version:3.e.19357
  869. [    2.383042] rga2 27930000.rga: Adding to iommu group 3
  870. [    2.383387] rga2 27930000.rga: probe successfully, irq = 49, hw_version:3.e.19357
  871. [    2.383652] rga_iommu: IOMMU binding successfully, default mapping core[0x4]
  872. [    2.383814] rga: Module initialized. v1.3.5
  873. [    2.406634] rockchip-csi2-dphy csi2-dcphy0: csi2 dphy0 probe successfully!
  874. [    2.407084] rockchip-csi2-dphy csi2-dphy3: csi2 dphy3 probe successfully!
  875. [    2.407409] mpp-iep2 27960000.iep: Adding to iommu group 4
  876. [    2.407721] mpp-iep2 27960000.iep: probe device
  877. [    2.407912] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
  878. [    2.407927] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
  879. [    2.407941] mpp-iep2 27960000.iep: reset_group->rw_sem_on=0
  880. [    2.407982] mpp-iep2 27960000.iep: allocate roi buffer failed
  881. [    2.408012] mpp-iep2 27960000.iep: probing finish
  882. [    2.408305] mpp_jpgdec 27910000.jpegd: Adding to iommu group 1
  883. [    2.408592] mpp_jpgdec 27910000.jpegd: probe device
  884. [    2.408799] mpp_jpgdec 27910000.jpegd: reset_group->rw_sem_on=0
  885. [    2.408815] mpp_jpgdec 27910000.jpegd: reset_group->rw_sem_on=0
  886. [    2.408885] mpp_jpgdec 27910000.jpegd: probing finish
  887. [    2.409139] mpp_jpgenc 27910800.jpege: Adding to iommu group 1
  888. [    2.409202] mpp_jpgenc 27910800.jpege: probe device
  889. [    2.409353] mpp_jpgenc 27910800.jpege: reset_group->rw_sem_on=0
  890. [    2.409364] mpp_jpgenc 27910800.jpege: reset_group->rw_sem_on=0
  891. [    2.409408] mpp_jpgenc 27910800.jpege: probe finish
  892. [    2.409673] mpp_rkvdec2 27b00100.rkvdec: Adding to iommu group 7
  893. [    2.409983] mpp_rkvdec2 27b00100.rkvdec: rkvdec, probing start
  894. [    2.410208] mpp_rkvdec2 27b00100.rkvdec: shared_niu_a is not found!
  895. [    2.410218] rkvdec2_init:1197: No niu aclk reset resource define
  896. [    2.410228] mpp_rkvdec2 27b00100.rkvdec: shared_niu_h is not found!
  897. [    2.410235] rkvdec2_init:1200: No niu hclk reset resource define
  898. [    2.410248] mpp_rkvdec2 27b00100.rkvdec: shared_video_cabac is not found!
  899. [    2.410256] rkvdec2_init:1206: No cabac reset resource define
  900. [    2.410292] mpp_rkvdec2 27b00100.rkvdec: no regulator, devfreq is disabled
  901. [    2.410462] mpp_rkvdec2 27b00100.rkvdec: sram_start 0x000000003ff88000
  902. [    2.410473] mpp_rkvdec2 27b00100.rkvdec: rcb_iova 0x0000000010000000
  903. [    2.410481] mpp_rkvdec2 27b00100.rkvdec: sram_size 491520
  904. [    2.410489] mpp_rkvdec2 27b00100.rkvdec: rcb_size 491520
  905. [    2.410498] mpp_rkvdec2 27b00100.rkvdec: min_width 512
  906. [    2.410528] mpp_rkvdec2 27b00100.rkvdec: link mode probe finish
  907. [    2.410580] mpp_rkvdec2 27b00100.rkvdec: probing finish
  908. [    2.410599] mpp_rkvdec2 27b00100.rkvdec: probing finish
  909. [    2.410849] mpp_rkvenc2 27a00000.rkvenc-core: Adding to iommu group 5
  910. [    2.411140] mpp_rkvenc2 27a00000.rkvenc-core: probing start
  911. [    2.411342] mpp_rkvenc2 27a00000.rkvenc-core: failed to init opp info
  912. [    2.411352] mpp_rkvenc2 27a00000.rkvenc-core: failed to init_opp_table
  913. [    2.411360] rkvenc_init:2147: failed to add venc devfreq
  914. [    2.411421] mpp_rkvenc2 27a00000.rkvenc-core: attach ccu as core 0
  915. [    2.411466] mpp_rkvenc2 27a00000.rkvenc-core: probing finish
  916. [    2.411727] mpp_rkvenc2 27a10000.rkvenc-core: Adding to iommu group 6
  917. [    2.411957] mpp_rkvenc2 27a10000.rkvenc-core: probing start
  918. [    2.412177] mpp_rkvenc2 27a10000.rkvenc-core: failed to init opp info
  919. [    2.412187] mpp_rkvenc2 27a10000.rkvenc-core: failed to init_opp_table
  920. [    2.412195] rkvenc_init:2147: failed to add venc devfreq
  921. [    2.412251] mpp_rkvenc2 27a10000.rkvenc-core: attach ccu as core 1
  922. [    2.412296] mpp_rkvenc2 27a10000.rkvenc-core: probing finish
  923. [    2.412657] rockchip-vop2 27d00000.vop: Adding to iommu group 10
  924. [    2.413284] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp0 assign plane mask: Esmart0[0x4], primary plane phy id: Esmart0[2]
  925. [    2.413309] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp1 assign plane mask: [0x0], primary plane phy id: INVALID[-1]
  926. [    2.413325] rockchip-vop2 27d00000.vop: [drm:vop2_bind] vp2 assign plane mask: [0x0], primary plane phy id: INVALID[-1]
  927. [    2.413493] [drm] Esmart1-win0(possible_vp_mask = 0x00000006) has no possible crtcs
  928. [    2.413547] [drm] Esmart3-win0(possible_vp_mask = 0x00000006) has no possible crtcs
  929. [    2.413583] [drm] unsupported AFBC format NV12 little-endian (0x3231564e)
  930. [    2.413648] [drm] failed to init overlay plane Cluster0-win1
  931. [    2.413716] [drm] failed to init overlay plane Cluster1-win1
  932. [    2.413870] rockchip-vop2 27d00000.vop: bin=0
  933. [    2.414089] rockchip-vop2 27d00000.vop: leakage=15
  934. [    2.414106] rockchip-vop2 27d00000.vop: leakage-volt-sel=1
  935. [    2.415047] rockchip-vop2 27d00000.vop: avs=0
  936. [    2.415173] rockchip-vop2 27d00000.vop: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  937. [    2.415207] debugfs: Directory 'vdd_logic_s0' with parent 'vdd_logic_s0' already present!
  938. [    2.416363] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
  939. [    2.417598] rockchip-vop2 27d00000.vop: Supported VOP aclk dvfs, normal mode:500000000, reset mode:594000000, advanced mode:702000000
  940. [    2.417614] rockchip-drm display-subsystem: bound 27d00000.vop (ops 0xffffffc0095ca918)
  941. [    2.419064] dwhdmi-rockchip 27da0000.hdmi: registered ddc I2C bus driver
  942. [    2.419681] rockchip-drm display-subsystem: bound 27da0000.hdmi (ops 0xffffffc0095e38c0)
  943. [    2.452664] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  944. [    2.452711] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  945. [    2.452738] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  946. [    2.452764] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  947. [    2.452790] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  948. [    2.452815] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  949. [    2.452841] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  950. [    2.452853] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  951. [    2.453157] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  952. [    2.453759] dwhdmi-rockchip 27da0000.hdmi: use tmds mode
  953. [    2.469523] dw-hdmi-qp-hdcp dw-hdmi-qp-hdcp.7.auto: dw_hdcp_qp_hdcp_probe success
  954. [    2.469680] [drm] Initialized rockchip 4.0.0 20140818 for display-subsystem on minor 0
  955. [    2.470657] <<GTP-INF>>[gt1x_ts_probe:560] GTP Driver Version: V1.4<2015/07/10>
  956. [    2.470676] <<GTP-INF>>[gt1x_ts_probe:561] GTP I2C Address: 0x14
  957. [    2.470718] <<GTP-ERR>>[gt1x_parse_dt:341] vdd_ana not specified, fallback to power-supply
  958. [    2.470720] mali 27800000.gpu: Kernel DDK version g21p0-01eac0
  959. [    2.470909] rockchip-dmc dmc: bin=0
  960. [    2.470996] <<GTP-INF>>[gt1x_parse_dt:348] Power Invert,no
  961. [    2.471043] mali 27800000.gpu: GPU metrics tracepoint support enabled
  962. [    2.471156] rockchip-dmc dmc: leakage=15
  963. [    2.471171] rockchip-dmc dmc: leakage-volt-sel=1
  964. [    2.471327] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
  965. [    2.471876] mali 27800000.gpu: bin=0
  966. [    2.472080] mali 27800000.gpu: leakage=6
  967. [    2.472115] debugfs: Directory '27800000.gpu-mali' with parent 'vdd_gpu_s0' already present!
  968. [    2.472765] mali 27800000.gpu: avs=0
  969. [    2.472778] W : [File] : drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 144; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
  970. [    2.473090] rockchip-dmc dmc: avs=0
  971. [    2.473110] rockchip-dmc dmc: current ATF version 0x100
  972. [    2.473311] rockchip-dmc dmc: normal_rate = 1560000000
  973. [    2.473320] rockchip-dmc dmc: reboot_rate = 2112000000
  974. [    2.473327] rockchip-dmc dmc: suspend_rate = 528000000
  975. [    2.473333] rockchip-dmc dmc: video_4k_rate = 1560000000
  976. [    2.473341] rockchip-dmc dmc: video_4k_10b_rate = 1560000000
  977. [    2.473347] rockchip-dmc dmc: video_svep_rate = 1560000000
  978. [    2.473354] rockchip-dmc dmc: boost_rate = 2112000000
  979. [    2.473361] rockchip-dmc dmc: fixed_rate(isp|cif0|cif1|dualview) = 2112000000
  980. [    2.473367] rockchip-dmc dmc: performance_rate = 2112000000
  981. [    2.473375] rockchip-dmc dmc: hdmirx_rate = 2112000000
  982. [    2.473381] rockchip-dmc dmc: deep_suspend_rate = 2112000000
  983. [    2.473395] rockchip-dmc dmc: failed to get vop pn to msch rl
  984. [    2.473547] rockchip-dmc dmc: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  985. [    2.473572] debugfs: Directory 'vdd_logic_s0' with parent 'vdd_logic_s0' already present!
  986. [    2.473951] mali 27800000.gpu: Register LUT 00070200 initialized for GPU arch 0x00070400
  987. [    2.473972] mali 27800000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
  988. [    2.474077] mali 27800000.gpu: No priority control manager is configured
  989. [    2.474085] mali 27800000.gpu: Large page allocation set to false after hardware feature check
  990. [    2.474336] mali 27800000.gpu: No memory group manager is configured
  991. [    2.474945] mali 27800000.gpu: EM: created perf domain
  992. [    2.474985] mali 27800000.gpu: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  993. [    2.476736] mali 27800000.gpu: * MALI kbase_mmap_min_addr compiled to CONFIG_DEFAULT_MMAP_MIN_ADDR, no runtime update possible! *
  994. [    2.476744] mali 27800000.gpu: Probed as mali0
  995. [    2.487470] rkcif rkcif-mipi-lvds: clear unready subdev num: 2
  996. [    2.487686] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  997. [    2.487700] rkcif-mipi-lvds: Async subdev notifier completed
  998. [    2.487712] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  999. [    2.487718] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
  1000. [    2.487725] rkcif rkcif-mipi-lvds3: clear unready subdev num: 2
  1001. [    2.487904] rkcif-mipi-lvds3: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  1002. [    2.487916] rkcif-mipi-lvds3: Async subdev notifier completed
  1003. [    2.487927] rkcif-mipi-lvds3: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  1004. [    2.487933] rkcif-mipi-lvds3: There is not terminal subdev, not synchronized with ISP
  1005. [    2.488013] rkcif-mipi-lvds3: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  1006. [    2.488027] rkcif-mipi-lvds3: There is not terminal subdev, not synchronized with ISP
  1007. [    2.488062] rkcif-mipi-lvds: rkcif_update_sensor_info: stream[0] get remote terminal sensor failed!
  1008. [    2.488072] rkcif-mipi-lvds: There is not terminal subdev, not synchronized with ISP
  1009. [    2.488529] RKNPU 27700000.npu: Adding to iommu group 0
  1010. [    2.488691] RKNPU 27700000.npu: RKNPU: rknpu iommu is enabled, using iommu mode
  1011. [    2.488868] dhd_module_init in
  1012. [    2.488993] dhd_wlan_init_plat_data, enter
  1013. [    2.488996] [WLAN_RFKILL]: rockchip_wifi_get_oob_irq: Enter
  1014. [    2.489029] dhd_wlan_init_plat_data, irq = 109
  1015. [    2.489060] Power-up adapter 'DHD generic adapter'
  1016. [    2.489086] wifi_platform_set_power = 1, delay: 200 msec
  1017. [    2.489093] [WLAN_RFKILL]: rockchip_wifi_power: 1
  1018. [    2.489099] [WLAN_RFKILL]: rockchip_wifi_power: toggle = false
  1019. [    2.489106] [WLAN_RFKILL]: wifi turn on power [GPIO-1-0]
  1020. [    2.489384] RKNPU 27700000.npu: can't request region for resource [mem 0x27700000-0x27707fff]
  1021. [    2.489420] RKNPU 27700000.npu: can't request region for resource [mem 0x27708000-0x2770ffff]
  1022. [    2.489715] [drm] Initialized rknpu 0.9.7 20240424 for 27700000.npu on minor 1
  1023. [    2.490898] RKNPU 27700000.npu: bin=0
  1024. [    2.491123] RKNPU 27700000.npu: leakage=5
  1025. [    2.491178] debugfs: Directory '27700000.npu-rknpu' with parent 'vdd_npu_s0' already present!
  1026. [    2.492449] RKNPU 27700000.npu: avs=0
  1027. [    2.492707] RKNPU 27700000.npu: EM: created perf domain
  1028. [    2.492767] RKNPU 27700000.npu: l=15000 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
  1029. [    2.493790] RKNPU 27700000.npu: RKNPU: nbuf region: [0x000000003fe80000, 0x000000003ff80000), nbuf size: 0x100000
  1030. [    2.494409] cfg80211: Loading compiled-in X.509 certificates for regulatory database
  1031. [    2.495687] cfg80211: Loaded X.509 cert 'wens: 61c038651aabdcf94bd0ac7ff06c7248db18c600'
  1032. [    2.496068] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
  1033. [    2.496320] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
  1034. [    2.496333] cfg80211: failed to load regulatory.db
  1035. [    2.497374] rockchip-pm rockchip-suspend: not set pwm-regulator-config
  1036. [    2.497951] rockchip-suspend not set sleep-mode-config for mem-lite
  1037. [    2.497965] rockchip-suspend not set wakeup-config for mem-lite
  1038. [    2.497974] rockchip-suspend not set sleep-mode-config for mem-ultra
  1039. [    2.497982] rockchip-suspend not set wakeup-config for mem-ultra
  1040. [    2.498690] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 407; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '18:32:24', on 'Aug 13 2024'.
  1041. [    2.498980] Mali:
  1042. [    2.498982] Mali device driver loaded
  1043. [    2.498997] rkisp rkisp-vir0: clear unready subdev num: 1
  1044. [    2.499187] rkisp-vir0: Async subdev notifier completed
  1045. [    2.499222] rkisp rkisp-vir1: clear unready subdev num: 1
  1046. [    2.499377] rkisp-vir1: Async subdev notifier completed
  1047. [    2.499391] ALSA device list:
  1048. [    2.499401]   No soundcards found.
  1049. [    2.531907] mmc_host mmc0: Bus speed (slot 0) = 148500000Hz (slot req 150000000Hz, actual 148500000HZ div = 0)
  1050. [    2.531941] dwmmc_rockchip 2a320000.mmc: Successfully tuned phase to 0
  1051. [    2.534967] mmc0: new ultra high speed SDR104 SDIO card at address 0001
  1052. [    2.535272] dummy_probe: enter
  1053. [    2.535282] dummy_probe: func->num=0x1;
  1054. [    2.535290] dummy_probe: class=0xff; vendor=0x2d0; device=0x4373
  1055. [    2.535415] dummy_probe: enter
  1056. [    2.535424] dummy_probe: func->num=0x2;
  1057. [    2.535431] dummy_probe: class=0xff; vendor=0x2d0; device=0x4373
  1058. [    2.535550] dummy_probe: enter
  1059. [    2.535559] dummy_probe: func->num=0x3;
  1060. [    2.535566] dummy_probe: class=0xff; vendor=0x2d0; device=0x4373
  1061. [    2.544745] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1062. [    2.544815] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
  1063. [    2.544834] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
  1064. [    2.620849] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1065. [    2.620938] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
  1066. [    2.620964] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
  1067. [    2.696618] wifi_platform_bus_enumerate device present 1
  1068. [    2.696729] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1069. [    2.696746] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
  1070. [    2.696758] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
  1071. [    2.713106] bcmsdh_register: register client driver
  1072. [    2.713354] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
  1073. [    2.713583] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
  1074. [    2.713612] bus num (host idx)=0, slot num (rca)=1
  1075. [    2.713638] found adapter info 'DHD generic adapter'
  1076. [    2.713738] sdioh_attach: sd clock rate = 150000000
  1077. [    2.714370] F1 signature read @0x18000000=0x17204373
  1078. [    2.714583] sdioh_cis_read: func_cis_ptr[0]=0x10ac
  1079. [    2.722878] sdioh_cis_read: func_cis_ptr[1]=0x1000
  1080. [    2.729429] sdioh_cis_read: func_cis_ptr[2]=0x1038
  1081. [    2.738961] F1 signature OK, socitype:0x1 chip:0x4373 rev:0x0 pkg:0x2
  1082. [    2.739521] DHD: dongle ram size is set to 917504(orig 917504) at 0x160000
  1083. [    2.739605] wifi_platform_prealloc: failed to alloc static mem section 7
  1084. [    2.741154] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1085. [    2.741237] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1086. [    2.741273] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1087. [    2.741456] dhd_dbg_attach_pkt_monitor, 1528
  1088. [    2.741495] dhd_log_dump_init: kernel log buf size = 256KB; logdump_prsrv_tailsize = 80KB; limit prsrv tail size to = 38KB
  1089. [    2.744349] dhd_attach(): thread:dhd_watchdog_thread:df started
  1090. [    2.744911] dhd_attach(): thread:dhd_dpc:e0 started
  1091. [    2.745184] dhd_attach(): thread:dhd_rxf:e1 started
  1092. [    2.745205] dhd_deferred_work_init: work queue initialized
  1093. [    2.745265] get_mem_val_from_file: File [/data/misc/wifi/.memdump.info] doesn't exist
  1094. [    2.745275] dhd_get_memdump_info: MEMDUMP ENABLED = 3
  1095. [    2.745639] dhdsdio_probe_init: making DHD_BUS_DOWN
  1096. [    2.745995] Dongle Host Driver, version 100.10.107 (eab8fb7)
  1097. [    2.745995] Compiled in drivers/net/wireless/rockchip_wlan/infineon/bcmdhd on Sep  6 2024 at 15:29:47
  1098. [    2.746315] dhd_ioctl_entry_local: returning as busstate=0
  1099. [    2.746325] CFG80211-ERROR) wl_cfg80211_get_channel : chanspec failed (-19)
  1100. [    2.746477] Register interface [wlan0]  MAC: 00:90:4c:6c:7c:f8
  1101. [    2.746477]
  1102. [    2.746596] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
  1103. [    2.746692] dhd_module_init out
  1104. [    2.768582] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1105. [    2.768615] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
  1106. [    2.768623] <<GTP-INF>>[gt1x_reset_guitar:788] GTP RESET!
  1107. [    2.840811] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1108. [    2.840882] <<GTP-ERR>>[gt1x_init:2319] Reset guitar failed!
  1109. [    2.840909] <<GTP-ERR>>[gt1x_init:2345] Init failed, use default setting
  1110. [    2.841243] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
  1111. [    2.841283] <<GTP-ERR>>[gt1x_get_chip_type:895] I2c communication error.
  1112. [    2.841310] <<GTP-ERR>>[gt1x_init:2355] Get chip type failed!
  1113. [    2.841663] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
  1114. [    2.841702] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
  1115. [    2.948487] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
  1116. [    2.948502] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
  1117. [    3.056800] <<GTP-ERR>>[_do_i2c_read:390] I2c Transfer error! (-6)
  1118. [    3.056870] <<GTP-ERR>>[gt1x_read_version:845] Read version failed!
  1119. [    3.164402] <<GTP-INF>>[gt1x_read_version:863] IC VERSION:GT_000000(Patch)_0000(Mask)_00(SensorID)
  1120. [    3.164475] <<GTP-INF>>[gt1x_init_panel:606] Config group0 used, length:239
  1121. [    3.164508] <<GTP-INF>>[gt1x_init_panel:657] X_MAX=4096,Y_MAX=4096,TRIGGER=0x01,WAKEUP_LEVEL=1
  1122. [    3.396379] rk3x-i2c 27300000.i2c: timeout, ipd: 0x30, state: 3
  1123. [    3.396458] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-110)
  1124. [    3.628363] rk3x-i2c 27300000.i2c: timeout, ipd: 0x30, state: 3
  1125. [    3.628438] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-110)
  1126. [    3.860354] rk3x-i2c 27300000.i2c: timeout, ipd: 0x30, state: 3
  1127. [    3.860427] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-110)
  1128. [    3.860762] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-6)
  1129. [    4.092396] rk3x-i2c 27300000.i2c: timeout, ipd: 0x30, state: 3
  1130. [    4.092469] <<GTP-ERR>>[_do_i2c_write:432] I2c transfer error! (-110)
  1131. [    4.092501] <<GTP-ERR>>[gt1x_send_cfg:551] Send config failed!
  1132. [    4.092528] <<GTP-ERR>>[gt1x_init:2367] Init panel failed.
  1133. [    4.093107] <<GTP-ERR>>[gt1x_ts_probe:587] GTP init failed!!!
  1134. [    4.093302] Goodix-TS-GT1X: probe of 0-0014 failed with error -2147483644
  1135. [    4.099559] EXT4-fs (sda7): recovery complete
  1136. [    4.099608] EXT4-fs (sda7): mounted filesystem with ordered data mode. Quota mode: disabled.
  1137. [    4.099676] VFS: Mounted root (ext4 filesystem) on device 8:7.
  1138. [    4.100975] devtmpfs: mounted
  1139. [    4.106664] Freeing unused kernel memory: 7616K
  1140. [    4.116469] Run /sbin/init as init process
  1141. [    4.229225] systemd[1]: System time before build time, advancing clock.
  1142. [    4.237670] systemd[1]: Failed to look up module alias 'autofs4': Function not implemented
  1143. [    4.242365] systemd[1]: systemd 247.3-7+deb11u5 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD +SECCOMP +BLKID +ELFUTILS +KMOD +IDN2 -IDN +PCRE2 default-hierarchy=unified)
  1144. [    4.243453] systemd[1]: Detected architecture arm64.

  1146. Welcome to Debian GNU/Linux 11 (bullseye)!

  1148. [    4.247601] systemd[1]: Set hostname to <debian.toybrick>.
  1149. [    4.248280] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1150. [    4.248488] CFG80211-ERROR) wl_cfg80211_netdev_notifier_call : wdev null. Do nothing
  1151. [    4.521592] systemd[1]: /lib/systemd/system/plymouth-start.service:16: Unit configured to use KillMode=none. This is unsafe, as it disables systemd's process lifecycle management for the service. Please update your service to use a safer KillMode=, such as 'mixed' or 'control-group'. Support for KillMode=none is deprecated and will eventually be removed.
  1152. [    4.564974] systemd[1]: Queued start job for default target Graphical Interface.
  1153. [    4.565666] systemd[1]: system-getty.slice: unit configures an IP firewall, but the local system does not support BPF/cgroup firewalling.
  1154. [  OK  ] Created slice system-getty.slice.
  1155. [    4.565686] systemd[1]: (This warning is only shown for the first unit using IP firewalling.)
  1156. [  OK  ] Created slice system-modprobe.slice.
  1157. [    4.566145] systemd[1]: Created slice system-getty.slice.
  1158. [  OK  ] Created slice system-serial\x2dgetty.slice.
  1159. [    4.566678] systemd[1]: Created slice system-modprobe.slice.
  1160. [  OK  ] Created slice system-systemd\x2dfsck.slice.
  1161. [    4.566949] systemd[1]: Created slice system-serial\x2dgetty.slice.
  1162. [  OK  ] Created slice User and Session Slice.
  1163. [    4.567183] systemd[1]: Created slice system-systemd\x2dfsck.slice.
  1164. [  OK  ] Started Forward Password R…uests to Wall Directory Watch.
  1165. [    4.567399] systemd[1]: Created slice User and Session Slice.
  1166. [  OK  ] Reached target User and Group Name Lookups.
  1167. [    4.567584] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
  1168. [  OK  ] Reached target Remote File Systems.
  1169. [    4.567750] systemd[1]: Condition check resulted in Arbitrary Executable File Formats File System Automount Point being skipped.
  1170. [  OK  ] Reached target Slices.
  1171. [    4.567876] systemd[1]: Reached target User and Group Name Lookups.
  1172. [  OK  ] Reached target Swap.
  1173. [    4.567945] systemd[1]: Reached target Remote File Systems.
  1174. [  OK  ] Listening on Syslog Socket.
  1175. [    4.568005] systemd[1]: Reached target Slices.
  1176. [  OK  ] Listening on fsck to fsckd communication Socket.
  1177. [    4.568071] systemd[1]: Reached target Swap.
  1178. [  OK  ] Listening on initctl Compatibility Named Pipe.
  1179. [    4.568690] systemd[1]: Listening on Syslog Socket.
  1180. [  OK  ] Listening on Journal Socket (/dev/log).
  1181. [    4.569046] systemd[1]: Listening on fsck to fsckd communication Socket.
  1182. [  OK  ] Listening on Journal Socket.
  1183. [    4.569261] systemd[1]: Listening on initctl Compatibility Named Pipe.
  1184. [  OK  ] Listening on udev Control Socket.
  1185. [    4.577028] systemd[1]: Condition check resulted in Journal Audit Socket being skipped.
  1186. [  OK  ] Listening on udev Kernel Socket.
  1187. [    4.577320] systemd[1]: Listening on Journal Socket (/dev/log).
  1188.          Mounting Kernel Debug File System...
  1189. [    4.577634] systemd[1]: Listening on Journal Socket.
  1190.          Mounting Kernel Trace File System...
  1191. [    4.578358] systemd[1]: Listening on udev Control Socket.
  1192. [    4.578671] systemd[1]: Listening on udev Kernel Socket.
  1193. [    4.578971] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
  1194.          Starting Load Kernel Module configfs...
  1195. [    4.579107] systemd[1]: Condition check resulted in POSIX Message Queue File System being skipped.
  1196. [    4.580901] systemd[1]: Mounting Kernel Debug File System...
  1197. [    4.583750] systemd[1]: Mounting Kernel Trace File System...
  1198. [    4.584916] systemd[1]: Condition check resulted in Create list of static device nodes for the current kernel being skipped.
  1199.          Starting Load Kernel Module drm...
  1200. [    4.587621] systemd[1]: Starting Load Kernel Module configfs...
  1201. [    4.590959] systemd[1]: Starting Load Kernel Module drm...
  1202. [    4.594964] systemd[1]: Starting Load Kernel Module fuse...
  1203.          Starting Load Kernel Module fuse...
  1204. [    4.597361] systemd[1]: Condition check resulted in Set Up Additional Binary Formats being skipped.
  1205. [    4.600131] systemd[1]: Starting Journal Service...
  1206.          Starting Journal Service...
  1207. [    4.604510] systemd[1]: Starting Load Kernel Modules...
  1208.          Starting Load Kernel Modules...
  1209. [    4.607270] systemd[1]: Starting Remount Root and Kernel File Systems...
  1210.          Starting Remount Root and Kernel File Systems...
  1211. [    4.611059] systemd[1]: Starting Coldplug All udev Devices...
  1212.          Starting Coldplug All udev Devices...
  1213. [    4.617329] systemd[1]: Mounted Kernel Debug File System.
  1214. [  OK  ] Mounted Kernel Debug File System.
  1215. [    4.618047] systemd[1]: Mounted Kernel Trace File System.
  1216. [  OK  ] Mounted Kernel Trace File System.
  1217. [    4.618932] systemd[1]: modprobe@configfs.service: Succeeded.
  1218. [  OK  ] Finished Load Kernel Module configfs.
  1219. [    4.619431] systemd[1]: Finished Load Kernel Module configfs.
  1220. [    4.627667] systemd[1]: modprobe@drm.service: Succeeded.
  1221. [    4.628120] systemd[1]: Finished Load Kernel Module drm.
  1222. [  OK  ] Finished Load Kernel Module drm.
  1223. [    4.628996] systemd[1]: modprobe@fuse.service: Succeeded.
  1224. [  OK  ] Finished Load Kernel Module fuse.
  1225. [    4.629321] systemd[1]: Finished Load Kernel Module fuse.
  1226. [FAILED] Failed to start Load Kernel Modules.
  1227. [    4.629838] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
  1228. See 'systemctl status systemd-modules-load.service' for details.
  1229. [    4.630039] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
  1230. [  OK  ] Finished Remount Root and Kernel File Systems.
  1231. [    4.630325] systemd[1]: Failed to start Load Kernel Modules.
  1232.          Mounting FUSE Control File System...
  1233. [    4.631057] systemd[1]: Finished Remount Root and Kernel File Systems.
  1234. [    4.633336] systemd[1]: Mounting FUSE Control File System...
  1235. [    4.636368] systemd[1]: Mounting Kernel Configuration File System...
  1236.          Mounting Kernel Configuration File System...
  1237. [    4.638782] systemd[1]: Condition check resulted in Rebuild Hardware Database being skipped.
  1238. [    4.639183] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
  1239. [    4.641884] systemd[1]: Starting Load/Save Random Seed...
  1240.          Starting Load/Save Random Seed...
  1241. [    4.645563] systemd[1]: Starting Apply Kernel Variables...
  1242.          Starting Apply Kernel Variables...
  1243. [    4.649865] systemd[1]: Starting Create System Users...
  1244.          Starting Create System Users...
  1245. [    4.652900] systemd[1]: Mounted FUSE Control File System.
  1246. [  OK  ] Mounted FUSE Control File System.
  1247. [    4.653234] systemd[1]: Mounted Kernel Configuration File System.
  1248. [  OK  ] Mounted Kernel Configuration File System.
  1249. [    4.664916] systemd[1]: Finished Apply Kernel Variables.
  1250. [  OK  ] Finished Apply Kernel Variables.
  1251. [    4.666155] systemd[1]: Finished Load/Save Random Seed.
  1252. [  OK  ] Finished Load/Save Random Seed.
  1253. [    4.666454] systemd[1]: Condition check resulted in First Boot Complete being skipped.
  1254. [    4.675762] systemd[1]: Finished Create System Users.
  1255. [  OK  ] Finished Create System Users.
  1256. [    4.677134] systemd[1]: Starting Create Static Device Nodes in /dev...
  1257.          Starting Create Static Device Nodes in /dev...
  1258. [    4.696439] systemd[1]: Finished Create Static Device Nodes in /dev.
  1259. [  OK  ] Finished Create Static Device Nodes in /dev.
  1260. [    4.696686] systemd[1]: Reached target Local File Systems (Pre).
  1261. [  OK  ] Reached target Local File Systems (Pre).
  1262. [    4.696795] systemd[1]: Reached target Local File Systems.
  1263. [  OK  ] Reached target Local File Systems.
  1264. [    4.696910] systemd[1]: Condition check resulted in Load AppArmor profiles being skipped.
  1265.          Starting Tell Plymouth To Write Out Runtime Data...
  1266. [    4.697864] systemd[1]: Starting Tell Plymouth To Write Out Runtime Data...
  1267.          Starting Rule-based Manage…for Device Events and Files...
  1268. [    4.698050] systemd[1]: Condition check resulted in Store a System Token in an EFI Variable being skipped.
  1269. [    4.698177] systemd[1]: Condition check resulted in Commit a transient machine-id on disk being skipped.
  1270. [    4.699323] systemd[1]: Starting Rule-based Manager for Device Events and Files...
  1271. [    4.712246] systemd[1]: Finished Tell Plymouth To Write Out Runtime Data.
  1272. [  OK  ] Finished Tell Plymouth To Write Out Runtime Data.
  1273. [    4.753096] systemd[1]: Started Journal Service.
  1274. [  OK  ] Started Journal Service.
  1275.          Starting Flush Journal to Persistent Storage...
  1276. [    4.767833] systemd-journald[254]: Received client request to flush runtime journal.
  1277. [  OK  ] Finished Flush Journal to Persistent Storage.
  1278.          Starting Create Volatile Files and Directories...
  1279. [  OK  ] Started Rule-based Manager for Device Events and Files.
  1280. [    4.788307] rk-pcie 2a200000.pcie: PCIe Link Fail, LTSSM is 0x3, hw_retries=0
  1281. [  OK  ] Finished Coldplug All udev Devices.
  1282.          Starting Helper to synchronize boot up for ifupdown...
  1283.          Starting Show Plymouth Boot Screen...
  1284. [  OK  ] Finished Create Volatile Files and Directories.
  1285.          Starting Network Time Synchronization...
  1286.          Starting Update UTMP about System Boot/Shutdown...
  1287. [  OK  ] Finished Helper to synchronize boot up for ifupdown.
  1288.          Starting Raise network interfaces...
  1289. [  OK  ] Started Show Plymouth Boot Screen.
  1290. [  OK  ] Started Forward Password R…s to Plymouth Directory Watch.
  1291. [  OK  ] Reached target Local Encrypted Volumes.
  1292. [  OK  ] Finished Update UTMP about System Boot/Shutdown.
  1293. Boot0:Mar  1 2024 18:55:39, ver: 0.00
  1294. DDR 81dd75088a wesley.yao 24/04/16-11:19:41,fwver: v1.03
  1295. In
  1296. LPDDR4X, 2112MHz
  1297. channel[0] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
  1298. channel[1] BW=16 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=16 Size=4096MB
  1299. Manufacturer ID:0xff
  1300. CH0 RX Vref:25.7%, RX DQS Vref:31.2%, TX Vref:20.8%,21.8%
  1301. DQ roc:
  1302. p1 n1, p0 n0, p0 n0, p0 n1, p4 n6, p1 n0, p0 n0, p0 n2, p7 n0,
  1303. p1 n0, p2 n0, p3 n0, p0 n7, p0 n2, p3 n3, p1 n0, p1 n4, p5 n0,
  1304. DQ rds:
  1305. h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
  1306. h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0, h0 l0,
  1307. DQS roc: p0 n3, p2, n1

  1309. CH1 RX Vref:26.5%, RX DQS Vref:31.6%, TX Vref:22.8%,22.8%
  1310. DQ roc:
  1311. p5 n0, p6 n0, p6 n0, p6 n3, p0 n4, p4 n0, p2 n0, p2 n0, p4 n0,
  1312. p5 n0, p3 n0, p6 n1, p6 n0, p6 n0, p6 n0, p6 n0, p5 n0, p7 n0,
  1313. DQ rds:
  1314. h1 l0, h1 l0, h1 l0, h1 l0, h0 l0, h1 l0, h1 l0, h0 l0,
  1315. h1 l0, h1 l0, h0 l0, h0 l0, h1 l0, h1 l0, h1 l0, h0 l0,
  1316. DQS roc: p2 n0, p2, n0

  1318. stride=0x3, ddr_config=0x4
  1319. hash bank_mask0-3 0x0 0x880 0x1100 0x2200, rank_mask0 0x400400
  1320. change to F1: 528MHz
  1321. change to F2: 1068MHz
  1322. change to F3: 1560MHz
  1323. change to F0: 2112MHz
  1324. out
复制代码

本主题由 toybrick 于 前天 08:51 审核通过
回复

使用道具 举报

返回列表
高级模式
B Color Image Link Quote Code Smilies
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

产品中心 购买渠道 开源社区 Wiki教程 资料下载 关于Toybrick

瑞芯微电子股份有限公司所有       闽ICP备19006074号-1      闽公网安备 35010202001061号

快速回复 返回顶部 返回列表