rv1126通过usb接机械硬盘盒

rv1126通过usb接机械硬盘盒，没有挂载成功，从log看disconnect，请问有碰到过的吗？log如下：
[ 1010.752739] usb 1-1.4: new high-speed USB device number 7 using ehci-platform
[ 1010.865458] usb 1-1.4: New USB device found, idVendor=152d, idProduct=9561, bcdDevice= 1.05
[ 1010.865497] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[ 1010.865509] usb 1-1.4: Product: JMS56x Series
[ 1010.865519] usb 1-1.4: Manufacturer: JMicron
[ 1010.865536] usb 1-1.4: SerialNumber: 00000000000000000000
[ 1010.867781] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[ 1010.868361] usb-storage 1-1.4:1.0: Quirks match for vid 152d pid 9561: 4000000
[ 1010.868476] scsi host0: usb-storage 1-1.4:1.0
[ 1011.057551] usb 1-1.4: USB disconnect, device number 7

yymeme345 发表于 2021-9-4 01:20
想知道后续

你也遇到这个问题了吗？

[  106.051384] usb 1-1.4: new high-speed USB device number 4 using ehci-platform
[  106.166502] usb 1-1.4: New USB device found, idVendor=152d, idProduct=9561, bcdDevice= 1.05
[  106.166583] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=5
[  106.166614] usb 1-1.4: Product: JMS56x Series
[  106.166642] usb 1-1.4: Manufacturer: JMicron
[  106.166670] usb 1-1.4: SerialNumber: 00000000000000000000
[  106.171276] usb-storage 1-1.4:1.0: USB Mass Storage device detected
[  106.172012] usb-storage 1-1.4:1.0: Quirks match for vid 152d pid 9561: 4000000
[  106.172270] scsi host0: usb-storage 1-1.4:1.0
[  107.179608] scsi 0:0:0:0: Direct-Access     ST2000VX 000-1ES164       0105 PQ: 0 ANSI: 6
[  107.180946] sd 0:0:0:0: Attached scsi generic sg0 type 0
[  115.124610] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[  115.128056] sd 0:0:0:0: [sda] Write Protect is off
[  115.128128] sd 0:0:0:0: [sda] Mode Sense: 47 00 10 08
[  115.129542] sd 0:0:0:0: [sda] No Caching mode page found
[  115.129620] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  115.217530]  sda: sda1
[  115.224705] sd 0:0:0:0: [sda] Attached SCSI disk

重新插拔几次，出现上面的打印，看着应该是正常的，用fdisk -l命令，能看到/dev/sda1分区了，但是挂载的时候，用下面命令：
mount /dev/sda1 /media/usb0
mount: mounting /dev/sda1 on /media/usb0 failed: Invalid argument
用-t 指定文件系统类型的话，就会提示failed: No such device，对比看的rk3399pro上挂载的时候不指定-t是可以成功挂载的