|
楼主 |
发表于 2019-2-19 15:05:17
|
显示全部楼层
替换原生下载的recovery 后,启动下,后又重启。串口log
20181010
In
soft reset
SRX
Channel 0: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=32 Size=1024MB
Channel 1: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=32 Size=1024MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x20
ch 1 ddrconfig = 0x101, ddrsize = 0x20
pmugrf_os_reg[2] = 0x3280D280, stride = 0x9
OUT
Boot1: 2018-08-06, version: 1.15
CPUId = 0x0
ChipType = 0x10, 275
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=15028MB
FwPartOffset=2000 , 100000
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
SdmmcInit=0 1
StorageInit ok = 78050
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0
GPT part: 0, name: uboot, start:0x2000, size:0x2000
GPT part: 1, name: trust, start:0x4000, size:0x2000
GPT part: 2, name: misc, start:0x6000, size:0x2000
GPT part: 3, name: boot, start:0x8000, size:0x10000
GPT part: 4, name: recovery, start:0x18000, size:0x20000
GPT part: 5, name: backup, start:0x38000, size:0x38000
GPT part: 6, name: security, start:0x70000, size:0x2000
GPT part: 7, name: cache, start:0x72000, size:0x100000
GPT part: 8, name: system, start:0x172000, size:0x500000
GPT part: 9, name: metadata, start:0x672000, size:0x8000
GPT part: 10, name: vendor, start:0x67a000, size:0x100000
GPT part: 11, name: oem, start:0x77a000, size:0x100000
GPT part: 12, name: frp, start:0x87a000, size:0x400
GPT part: 13, name: userdata, start:0x87a400, size:0x14dfbdf
find partition:uboot OK. first_lba:0x2000.
find partition:trust OK. first_lba:0x4000.
LoadTrust Addr:0x4000
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xe2f68
RunBL31 0x10000
NOTICE: BL31: v1.3(debug):d80d566
NOTICE: BL31: Built : 09:42:16, Nov 21 2018
NOTICE: BL31: Rockchip release version: v1.1
INFO: GICv3 with legacy support detected. ARM GICV3 driver initialized in EL3
INFO: Using opteed sec cpu_context!
INFO: boot cpu mask: 0
INFO: plat_rockchip_pmu_init(1162): pd status 3e
INFO: BL31: Initializing runtime services
INFO: BL31: Initializing BL32
INF [0x0] TEE-CORE:init_primary_helper:337: Initializing (1.1.0-195-g8f090d20 #6 Fri Dec 7 06:11:20 UTC 2018 aarch64)
INF [0x0] TEE-CORE:init_primary_helper:338: Release version: 1.2
INF [0x0] TEE-CORE:init_teecore:83: teecore inits done
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0x200000
INFO: SPSR = 0x3c9
U-Boot 2017.09-gb73946f-dirty (Feb 19 2019 - 14:25:47 +0800)
Model: Rockchip RK3399 Evaluation Board
DRAM: 2 GiB
Relocation Offset is: 7dbe2000
Using default environment
dwmmc@fe320000: 1, sdhci@fe330000: 0
Card did not respond to voltage select!
mmc_init: -95, time 9
switch to partitions #0, OK
mmc0(part 0) is current device
Bootdev: mmc 0
PartType: EFI
Load FDT from recovery part
DTB: rk-kernel.dtb
I2c speed: 400000Hz
PMIC: RK8090 (on=0x69, off=0x37)
vdd_center 900000 uV
vdd_cpu_l 900000 uV
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
enter Recovery mode!
CLK:
aplll 816000 KHz
apllb 24000 KHz
dpll 800000 KHz
cpll 24000 KHz
gpll 800000 KHz
npll 600000 KHz
vpll 24000 KHz
aclk_perihp 133333 KHz
hclk_perihp 66666 KHz
pclk_perihp 33333 KHz
aclk_perilp0 266666 KHz
hclk_perilp0 88888 KHz
pclk_perilp0 44444 KHz
hclk_perilp1 100000 KHz
pclk_perilp1 50000 KHz
Net: eth0: ethernet@fe300000
Hit key to stop autoboot('CTRL+C'): 0
ANDROID: reboot reason: "recovery"
Booting kernel at 0x00280000 with fdt at 1f00000...
## Booting Android Image at 0x0027f800 ...
Kernel load addr 0x00280000 size 19081 KiB
RAM disk load addr 0x01522800 size 8602 KiB
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
XIP Kernel Image ... OK
'reserved-memory' secure-memory@20000000: addr=20000000 size=10000000
Loading Ramdisk to 7b56d000, end 7bdd3580 ... OK
Loading Device Tree to 000000007b551000, end 000000007b56c7e1 ... OK
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x0a200000 - 0x80000000 (size: 0x75e00000)
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Initializing cgroup subsys schedtune
[ 0.000000] Linux version 4.4.167 (kfx@inno) (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05) ) #13 SMP PREEMPT Sat Jan 19 00:48:38 CST 2019
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] earlycon: Early serial console at MMIO32 0xff1a0000 (options '')
[ 0.000000] bootconsole [uart0] enabled
[ 0.000000] Reserved memory: failed to reserve memory for node 'drm-logo@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] Reserved memory: failed to reserve memory for node 'stb-devinfo@00000000': base 0x0000000000000000, size 0 MiB
[ 0.000000] cma: Reserved 16 MiB at 0x000000007f000000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] PERCPU: Embedded 21 pages/cpu @ffffffc07eeee000 s45528 r8192 d32296 u86016
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 507912
[ 0.000000] Kernel command line: storagemedia=emmc androidboot.mode=emmc androidboot.slot_suffix= androidboot.serialno=TD033101190100153 buildvariant=userdebug console=ttyFIQ0 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.veritymode=enforcing androidboot.hardware=rk30board androidboot.console=ttyFIQ0 init=/init earlycon=uart8250,mmio32,0xff1a0000 swiotlb=1
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] software IO TLB [mem 0x7eea6000-0x7eee6000] (0MB) mapped at [ffffffc07eea6000-ffffffc07eee5fff]
[ 0.000000] Memory: 1980504K/2064384K available (11134K kernel code, 1736K rwdata, 5376K rodata, 768K init, 2412K bss, 67496K reserved, 16384K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbdbfff0000 ( 246 GB)
[ 0.000000] .init : 0xffffff80090b0000 - 0xffffff8009170000 ( 768 KB)
[ 0.000000] .text : 0xffffff8008080000 - 0xffffff8008b60000 ( 11136 KB)
[ 0.000000] .rodata : 0xffffff8008b60000 - 0xffffff80090b0000 ( 5440 KB)
[ 0.000000] .data : 0xffffff8009170000 - 0xffffff8009322008 ( 1737 KB)
[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)
[ 0.000000] 0xffffffbdc0008000 - 0xffffffbdc2000000 ( 31 MB actual)
[ 0.000000] fixed : 0xffffffbffe7fb000 - 0xffffffbffec00000 ( 4116 KB)
[ 0.000000] PCI I/O : 0xffffffbffee00000 - 0xffffffbfffe00000 ( 16 MB)
[ 0.000000] memory : 0xffffffc000200000 - 0xffffffc080000000 ( 2046 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] ITS: /interrupt-controller@fee00000/interrupt-controller@fee20000
[ 0.000000] ITS: allocated 65536 Devices @a200000 (psz 64K, shr 0)
[ 0.000000] ITS: using cache flushing for cmd queue
[ 0.000000] GIC: using LPI property table @0x000000000a280000
[ 0.000000] ITS: Allocated 1792 chunks for LPIs
[ 0.000000] CPU0: found redistributor 0 region 0:0x00000000fef00000
[ 0.000000] CPU0: using LPI pending table @0x000000000a290000
[ 0.000000] GIC: using cache flushing for LPI property table
[ 0.000000] GIC: PPI partition interrupt-partition-0[0] { /cpus/cpu@0[0] /cpus/cpu@1[1] /cpus/cpu@2[2] /cpus/cpu@3[3] }
[ 0.000000] GIC: PPI partition interrupt-partition-1[1] { /cpus/cpu@100[4] /cpus/cpu@101[5] }
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop0_frac as parent of dclk_vop0, rate changes may not work
[ 0.000000] rockchip_clk_register_frac_branch: could not find dclk_vop1_frac as parent of dclk_vop1, rate changes may not work
[ 0.000000] rockchip_cpuclk_pre_rate_change: limiting alt-divider 33 to 31
[ 0.000000] Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.002016] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[ 0.002996] pid_max: default: 32768 minimum: 301
[ 0.003517] Security Framework initialized
[ 0.003912] SELinux: Initializing.
[ 0.004326] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.004965] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.006386] Initializing cgroup subsys memory
[ 0.006826] Initializing cgroup subsys freezer
[ 0.008161] sched-energy: Sched-energy-costs installed from DT
[ 0.008719] CPU0: update cpu_capacity 401
[ 0.009177] ASID allocator initialised with 32768 entries
[ 0.026008] PCI/MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.027321] Platform MSI: /interrupt-controller@fee00000/interrupt-controller@fee20000 domain created
[ 0.039400] Detected VIPT I-cache on CPU1
[ 0.039432] CPU1: found redistributor 1 region 0:0x00000000fef20000
[ 0.039461] CPU1: using LPI pending table @0x000000000a3f0000
[ 0.039500] CPU1: update cpu_capacity 401
[ 0.039504] CPU1: Booted secondary processor [410fd034]
[ 0.049391] Detected VIPT I-cache on CPU2
[ 0.049411] CPU2: found redistributor 2 region 0:0x00000000fef40000
[ 0.049438] CPU2: using LPI pending table @0x000000007c020000
[ 0.049464] CPU2: update cpu_capacity 401
[ 0.049467] CPU2: Booted secondary processor [410fd034]
[ 0.059420] Detected VIPT I-cache on CPU3
[ 0.059439] CPU3: found redistributor 3 region 0:0x00000000fef60000
[ 0.059466] CPU3: using LPI pending table @0x000000007c060000
[ 0.059490] CPU3: update cpu_capacity 401
[ 0.059493] CPU3: Booted secondary processor [410fd034]
[ 0.069473] Detected PIPT I-cache on CPU4
[ 0.069499] CPU4: found redistributor 100 region 0:0x00000000fef80000
[ 0.069537] CPU4: using LPI pending table @0x000000007c0b0000
[ 0.069575] CPU4: update cpu_capacity 1024
[ 0.069578] CPU4: Booted secondary processor [410fd082]
[ 0.079493] Detected PIPT I-cache on CPU5
[ 0.079510] CPU5: found redistributor 101 region 0:0x00000000fefa0000
[ 0.079546] CPU5: using LPI pending table @0x000000007c0e0000
[ 0.079572] CPU5: update cpu_capacity 1024
[ 0.079574] CPU5: Booted secondary processor [410fd082]
[ 0.079657] Brought up 6 CPUs
[ 0.091963] SMP: Total of 6 processors activated.
[ 0.092413] CPU features: detected feature: GIC system register CPU interface
[ 0.093092] CPU features: detected feature: 32-bit EL0 Support
[ 0.093659] CPU: All CPU(s) started at EL2
[ 0.094084] alternatives: patching kernel code
[ 0.096408] devtmpfs: initialized
[ 0.118120] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[ 0.119067] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.120778] pinctrl core: initialized pinctrl subsystem
[ 0.124179] Failed to find legacy iommu devices
[ 0.125122] NET: Registered protocol family 16
[ 0.126269] schedtune: init normalization constants...
[ 0.126764] schedtune: CLUSTER[0-3] min_pwr: 56 max_pwr: 222
[ 0.127387] schedtune: CPU[0] min_pwr: 0 max_pwr: 222
[ 0.128021] schedtune: CPU[1] min_pwr: 0 max_pwr: 222
[ 0.128643] schedtune: CPU[2] min_pwr: 0 max_pwr: 222
[ 0.129264] schedtune: CPU[3] min_pwr: 0 max_pwr: 222
[ 0.129935] schedtune: CLUSTER[4-5] min_pwr: 65 max_pwr: 1108
[ 0.130544] schedtune: CPU[4] min_pwr: 0 max_pwr: 1108
[ 0.131148] schedtune: CPU[5] min_pwr: 0 max_pwr: 1108
[ 0.131746] schedtune: SYSTEM min_pwr: 121 max_pwr: 4434
[ 0.132345] schedtune: using normalization constants mul: 3862781856 sh1: 1 sh2: 12
[ 0.133062] schedtune: verify normalization constants...
[ 0.133547] schedtune: max_pwr/2^0: 4313 => norm_pwr: 1024
[ 0.134058] schedtune: max_pwr/2^1: 2156 => norm_pwr: 511
[ 0.134571] schedtune: max_pwr/2^2: 1078 => norm_pwr: 255
[ 0.135082] schedtune: max_pwr/2^3: 539 => norm_pwr: 127
[ 0.135596] schedtune: max_pwr/2^4: 269 => norm_pwr: 63
[ 0.136109] schedtune: max_pwr/2^5: 134 => norm_pwr: 31
[ 0.136632] schedtune: configured to support 5 boost groups
[ 0.146660] cpuidle: using governor ladder
[ 0.160031] cpuidle: using governor menu
[ 0.160434] Registered FIQ tty driver
[ 0.161497] vdso: 2 pages (1 code @ ffffff8008b66000, 1 data @ ffffff8009174000)
[ 0.162226] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.163641] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.193414] console [pstore-1] enabled
[ 0.193998] pstore: Registered ramoops as persistent store backend
[ 0.194572] ramoops: attached 0xf0000@0x110000, ecc: 0/0
[ 0.196292] fiq debugger fiq mode enabled
[[ 0.196984] console [ttyFIQ0] enabled
0.196984] console [ttyFIQ0] enabled
[ 0.197655] bootconsole [uart0] disabled
[ 0.197655] bootconsole [uart0] disabled
[ 0.198180] Registered fiq debugger ttyFIQ0
[ 0.230467] iommu: Adding device ff650000.vpu_service to group 0
[ 0.230559] iommu: Adding device ff660000.rkvdec to group 1
[ 0.230635] iommu: Adding device ff670000.iep to group 2
[ 0.230739] iommu: Adding device ff8f0000.vop to group 3
[ 0.230824] iommu: Adding device ff900000.vop to group 4
[ 0.230968] iommu: Adding device ff910000.isp to group 5
[ 0.231055] iommu: Adding device ff920000.isp to group 6
[ 0.231451] rk_iommu ff650800.iommu: can't get sclk
[ 0.231696] rk_iommu ff660480.iommu: can't get sclk
[ 0.231792] rk_iommu ff670800.iommu: can't get aclk
[ 0.231803] rk_iommu ff670800.iommu: can't get hclk
[ 0.231814] rk_iommu ff670800.iommu: can't get sclk
[ 0.231977] rk_iommu ff8f3f00.iommu: can't get sclk
[ 0.232128] rk_iommu ff903f00.iommu: can't get sclk
[ 0.232280] rk_iommu ff914000.iommu: can't get sclk
[ 0.232425] rk_iommu ff924000.iommu: can't get sclk
[ 0.232752] SCSI subsystem initialized
[ 0.232927] usbcore: registered new interface driver usbfs
[ 0.232971] usbcore: registered new interface driver hub
[ 0.233041] usbcore: registered new device driver usb
[ 0.233484] media: Linux media interface: v0.10
[ 0.233521] Linux video capture interface: v2.00
[ 0.233717] pps_core: LinuxPPS API ver. 1 registered
[ 0.233726] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.233745] PTP clock support registered
[ 0.235470] Advanced Linux Sound Architecture Driver Initialized.
[ 0.235975] Bluetooth: Core ver 2.21
[ 0.236007] NET: Registered protocol family 31
[ 0.236015] Bluetooth: HCI device and connection manager initialized
[ 0.236028] Bluetooth: HCI socket layer initialized
[ 0.236040] Bluetooth: L2CAP socket layer initialized
[ 0.236064] Bluetooth: SCO socket layer initialized
[ 0.236808] rockchip-cpuinfo cpuinfo: Serial : b3ac0c2cb615bf38
[ 0.237303] clocksource: Switched to clocksource arch_sys_counter
[ 0.280963] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[ 0.281211] NET: Registered protocol family 2
[ 0.281661] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.281806] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.282079] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.282159] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.282217] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.282391] NET: Registered protocol family 1
[ 0.283331] Trying to unpack rootfs image as initramfs...
[ 0.661066] Freeing initrd memory: 8600K
[ 0.661629] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 0.661718] hw perfevents: enabled with armv8_cortex_a72 PMU driver, 7 counters available
[ 0.664648] audit: initializing netlink subsys (disabled)
[ 0.664711] audit: type=2000 audit(0.660:1): initialized
[ 0.670115] VFS: Disk quotas dquot_6.6.0
[ 0.670249] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.671193] Registering sdcardfs 0.1
[ 0.671774] fuse init (API version 7.23)
[ 0.672949]
[ 0.672949] TEE Core Framework initialization (ver 1:0.1)
[ 0.672978] TEE armv7 Driver initialization
[ 0.673354] tz_tee_probe: name="armv7sec", id=0, pdev_name="armv7sec.0"
[ 0.673371] TEE core: Alloc the misc device "opteearmtz00" (id=0)
[ 0.673543] TEE Core: Register the misc device "opteearmtz00" (id=0,minor=62)
[ 0.677876] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[ 0.677904] io scheduler noop registered
[ 0.678067] io scheduler cfq registered (default)
[ 0.679003] rockchip-usb2phy ff770000.syscon:usb2-phy@e460: failed to create phy
[ 0.683715] rockchip-pcie f8000000.pcie: no vpcie3v3 regulator found
[ 0.683742] rockchip-pcie f8000000.pcie: no vpcie1v8 regulator found
[ 0.683756] rockchip-pcie f8000000.pcie: no vpcie0v9 regulator found
[ 0.683767] rockchip-pcie f8000000.pcie: missing "memory-region" property
[ 0.683783] PCI host bridge /pcie@f8000000 ranges:
[ 0.683812] MEM 0xfa000000..0xfbdfffff -> 0xfa000000
[ 0.683823] IO 0xfbe00000..0xfbefffff -> 0xfbe00000
[ 1.227359] rockchip-pcie f8000000.pcie: PCIe link training gen1 timeout!
[ 1.227427] rockchip-pcie f8000000.pcie: deferred probe failed
[ 1.227570] rockchip-pcie: probe of f8000000.pcie failed with error -110
[ 1.228299] backlight supply power not found, using dummy regulator
[ 1.228921] iep: failed to find iep power down clock source.
[ 1.229510] IEP Power ON
[ 1.229891] IEP Power OFF
[ 1.230014] IEP Driver loaded succesfully
[ 1.230352] Module initialized.
[ 1.230794] rk-vcodec ff650000.vpu_service: no regulator for vcodec
[ 1.231124] rk-vcodec ff650000.vpu_service: probe device
[ 1.231327] rk-vcodec ff650000.vpu_service: drm allocator with mmu enabled
[ 1.231880] rk-vcodec ff650000.vpu_service: could not find power_model node
[ 1.231896] rk-vcodec ff650000.vpu_service: init success
[ 1.232082] rk-vcodec ff660000.rkvdec: no regulator for vcodec
[ 1.235831] rk-vcodec ff660000.rkvdec: probe device
[ 1.236019] rk-vcodec ff660000.rkvdec: drm allocator with mmu enabled
[ 1.236388] rk-vcodec ff660000.rkvdec: could not find power_model node
[ 1.236399] rk-vcodec ff660000.rkvdec: init success
[ 1.237968] dma-pl330 ff6d0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.237990] dma-pl330 ff6d0000.dma-controller: DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 1.239294] dma-pl330 ff6e0000.dma-controller: Loaded driver for PL330 DMAC-241330
[ 1.239315] dma-pl330 ff6e0000.dma-controller: DBUFF-128x8bytes Num_Chans-8 Num_Peri-20 Num_Events-16
[ 1.240918] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[ 1.241485] ff180000.serial: ttyS0 at MMIO 0xff180000 (irq = 38, base_baud = 1500000) is a 16550A
[ 1.241955] ff370000.serial: ttyS4 at MMIO 0xff370000 (irq = 40, base_baud = 1500000) is a 16550A
[ 1.242359] [drm] Initialized drm 1.1.0 20060810
[ 1.246216] [drm] Rockchip DRM driver version: v1.0.1
[ 1.249175] Unable to detect cache hierarchy for CPU 0
[ 1.257245] brd: module loaded
[ 1.262189] loop: module loaded
[ 1.262700] zram: Added device: zram0
[ 1.263649] SCSI Media Changer driver v0.25
[ 1.264403] tun: Universal TUN/TAP device driver, 1.6
[ 1.264418] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.265502] rk_gmac-dwmac fe300000.ethernet: clock input or output? (input).
[ 1.265526] rk_gmac-dwmac fe300000.ethernet: TX delay(0x28).
[ 1.265537] rk_gmac-dwmac fe300000.ethernet: RX delay(0x11).
[ 1.265561] rk_gmac-dwmac fe300000.ethernet: integrated PHY? (no).
[ 1.265724] rk_gmac-dwmac fe300000.ethernet: cannot get clock clk_mac_speed
[ 1.265738] rk_gmac-dwmac fe300000.ethernet: clock input from PHY
[ 1.270753] rk_gmac-dwmac fe300000.ethernet: init for RGMII
[ 1.270876] stmmac - user ID: 0x10, Synopsys ID: 0x35
[ 1.270889] Ring mode enabled
[ 1.270897] DMA HW capability register supported
[ 1.270904] Normal descriptors
[ 1.270913] RX Checksum Offload Engine supported (type 2)
[ 1.270920] TX Checksum insertion supported
[ 1.270926] Wake-Up On Lan supported
[ 1.270971] Enable RX Mitigation via HW Watchdog Timer
[ 1.340733] libphy: stmmac: probed
[ 1.340801] eth%d: PHY ID 001cc915 at 0 IRQ POLL (stmmac-0:00) active
[ 1.340813] eth%d: PHY ID 001cc915 at 1 IRQ POLL (stmmac-0:01)
[ 1.342269] PPP generic driver version 2.4.2
[ 1.342567] PPP BSD Compression module registered
[ 1.342628] PPP Deflate Compression module registered
[ 1.342709] PPP MPPE Compression module registered
[ 1.342735] NET: Registered protocol family 24
[ 1.342795] SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
[ 1.342804] CSLIP: code copyright 1989 Regents of the University of California.
[ 1.342826] Rockchip WiFi SYS interface (V1.00) ...
[ 1.342940] usbcore: registered new interface driver catc
[ 1.343041] usbcore: registered new interface driver kaweth
[ 1.343060] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 1.343111] usbcore: registered new interface driver pegasus
[ 1.343212] usbcore: registered new interface driver rtl8150
[ 1.343267] usbcore: registered new interface driver r8152
[ 1.343284] hso: drivers/net/usb/hso.c: Option Wireless
[ 1.343353] usbcore: registered new interface driver hso
[ 1.343464] usbcore: registered new interface driver asix
[ 1.343521] usbcore: registered new interface driver ax88179_178a
[ 1.343576] usbcore: registered new interface driver cdc_ether
[ 1.343675] usbcore: registered new interface driver cdc_eem
[ 1.343730] usbcore: registered new interface driver dm9601
[ 1.343795] usbcore: registered new interface driver smsc75xx
[ 1.343916] usbcore: registered new interface driver smsc95xx
[ 1.343999] usbcore: registered new interface driver gl620a
[ 1.344088] usbcore: registered new interface driver net1080
[ 1.344144] usbcore: registered new interface driver plusb
[ 1.344204] usbcore: registered new interface driver rndis_host
[ 1.344267] usbcore: registered new interface driver cdc_subset
[ 1.344347] usbcore: registered new interface driver zaurus
[ 1.344403] usbcore: registered new interface driver MOSCHIP usb-ethernet driver
[ 1.344485] usbcore: registered new interface driver int51x1
[ 1.344563] usbcore: registered new interface driver kalmia
[ 1.344622] usbcore: registered new interface driver ipheth
[ 1.344685] usbcore: registered new interface driver sierra_net
[ 1.344765] usbcore: registered new interface driver cx82310_eth
[ 1.344833] usbcore: registered new interface driver cdc_ncm
[ 1.344893] usbcore: registered new interface driver qmi_wwan
[ 1.344964] usbcore: registered new interface driver cdc_mbim
[ 1.346754] rockchip-dwc3 usb0: failed to get drvdata dwc3
[ 1.348141] rockchip-dwc3 usb1: failed to get drvdata dwc3
[ 1.349537] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.349568] ehci-pci: EHCI PCI platform driver
[ 1.349659] ehci-platform: EHCI generic platform driver
[ 1.350463] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.350501] ohci-platform: OHCI generic platform driver
[ 1.351745] usbcore: registered new interface driver usblp
[ 1.351816] usbcore: registered new interface driver cdc_wdm
[ 1.351870] usbcore: registered new interface driver uas
[ 1.351942] usbcore: registered new interface driver usb-storage
[ 1.352002] usbcore: registered new interface driver ums-alauda
[ 1.352052] usbcore: registered new interface driver ums-cypress
[ 1.352105] usbcore: registered new interface driver ums-datafab
[ 1.352158] usbcore: registered new interface driver ums_eneub6250
[ 1.352216] usbcore: registered new interface driver ums-freecom
[ 1.352265] usbcore: registered new interface driver ums-isd200
[ 1.352314] usbcore: registered new interface driver ums-jumpshot
[ 1.352368] usbcore: registered new interface driver ums-karma
[ 1.352427] usbcore: registered new interface driver ums-onetouch
[ 1.352477] usbcore: registered new interface driver ums-sddr09
[ 1.352529] usbcore: registered new interface driver ums-sddr55
[ 1.352583] usbcore: registered new interface driver ums-usbat
[ 1.352696] usbcore: registered new interface driver usbserial
[ 1.352741] usbcore: registered new interface driver usbserial_generic
[ 1.352779] usbserial: USB Serial support registered for generic
[ 1.352831] usbcore: registered new interface driver option
[ 1.352877] usbserial: USB Serial support registered for GSM modem (1-port)
[ 1.352945] usbcore: registered new interface driver cdc_xr_usb_serial
[ 1.352955] xr_usb_serial_common: Exar USB UART (serial port) driver
[ 1.353013] usbcore: registered new interface driver trancevibrator
[ 1.353043] usb20_otg: version 3.10a 21-DEC-2012
[ 1.353277] usb20_host: version 3.10a 21-DEC-2012
[ 1.354040] usbcore: registered new interface driver xpad
[ 1.354111] usbcore: registered new interface driver usb_acecad
[ 1.354170] usbcore: registered new interface driver aiptek
[ 1.354268] usbcore: registered new interface driver gtco
[ 1.354328] usbcore: registered new interface driver hanwang
[ 1.354387] usbcore: registered new interface driver kbtab
[ 1.355045] sensor_register_slave:kxtj9,id=11
[ 1.355071] sensor_register_slave:mma8452,id=17
[ 1.355089] sensor_register_slave:lis3dh,id=7
[ 1.355111] sensor_register_slave:mma7660,id=18
[ 1.355127] sensor_register_slave:lsm303d,id=22
[ 1.355141] sensor_register_slave:gs_mc3230,id=23
[ 1.355150] [Gsensor] gsensor_init
[ 1.355165] sensor_register_slave:mpu6880_acc,id=24
[ 1.355180] sensor_register_slave:mpu6500_acc,id=25
[ 1.355195] sensor_register_slave:lsm330_acc,id=26
[ 1.355210] sensor_register_slave:bma2xx_acc,id=27
[ 1.355225] sensor_register_slave:akm8975,id=30
[ 1.355240] sensor_register_slave:akm8963,id=31
[ 1.355255] sensor_register_slave:l3g4200d,id=45
[ 1.355271] sensor_register_slave:l3g20d,id=46
[ 1.355286] sensor_register_slave:ewtsa,id=47
[ 1.355302] sensor_register_slave:lsm330_gyro,id=51
[ 1.355331] sensor_register_slave:cm3217,id=53
[ 1.355346] sensor_register_slave:cm3218,id=54
[ 1.355361] sensor_register_slave:ls_stk3410,id=62
[ 1.355377] sensor_register_slave:ps_stk3410,id=67
[ 1.356497] i2c /dev entries driver
[ 1.358035] rk808 0-0020: Pmic Chip id: 0x8090
[ 1.358452] rk808 0-0020: source: on=0x40, off=0x00
[ 1.359274] rk808 0-0020: support dcdc3 fb mode:-22, 2081598496
[ 1.359570] rk808 0-0020: support pmic reset mode:-22,-64
[ 1.363032] rk808-regulator rk808-regulator: there is no dvs0 gpio
[ 1.363115] rk808-regulator rk808-regulator: there is no dvs1 gpio
[ 1.363274] DCDC_REG1: supplied by vcc5v0_sys
[ 1.364850] DCDC_REG2: supplied by vcc5v0_sys
[ 1.366502] DCDC_REG3: supplied by vcc5v0_sys
[ 1.367906] DCDC_REG4: supplied by vcc5v0_sys
[ 1.369261] DCDC_REG5: supplied by vcc5v0_sys
[ 1.370433] LDO_REG1: supplied by vcc_buck5
[ 1.372306] LDO_REG2: supplied by vcc_buck5
[ 1.374176] LDO_REG3: supplied by vcc_buck5
[ 1.375994] LDO_REG4: supplied by vcc_buck5
[ 1.377880] LDO_REG5: supplied by vcc_buck5
[ 1.379751] LDO_REG6: supplied by vcc_buck5
[ 1.381640] LDO_REG7: supplied by vcc3v3_sys
[ 1.383536] LDO_REG8: supplied by vcc3v3_sys
[ 1.385515] LDO_REG9: supplied by vcc3v3_sys
[ 1.387507] SWITCH_REG1: supplied by vcc5v0_sys
[ 1.388002] SWITCH_REG2: supplied by vcc3v3_sys
[ 1.389278] rk817-battery rk817-battery: Failed to find matching dt id
[ 1.389539] rk817-charger rk817-charger: Failed to find matching dt id
[ 1.391846] input: rk8xx_pwrkey as /devices/platform/ff3c0000.i2c/i2c-0/0-0020/input/input0
[ 1.395805] rk808-rtc rk808-rtc: rtc core: registered rk808-rtc as rtc0
[ 1.398130] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[ 1.398253] fan53555-reg: supplied by vcc5v0_sys
[ 1.400705] fan53555-regulator 0-0010: FAN53555 Option[0] Rev[15] Detected!
[ 1.400809] fan53555-reg: supplied by vcc5v0_sys
[ 1.402576] rk3x-i2c ff3c0000.i2c: Initialized RK3xxx I2C bus at ffffff800977c000
[ 1.403303] rk3x-i2c ff110000.i2c: Initialized RK3xxx I2C bus at ffffff800977e000
[ 1.403910] rk3x-i2c ff120000.i2c: Initialized RK3xxx I2C bus at ffffff80097e6000
[ 1.404624] rk3x-i2c ff160000.i2c: Initialized RK3xxx I2C bus at ffffff80097e8000
[ 1.406151] fusb302 8-0022: Can't get property of role, set role to default DRP
[ 1.414586] fusb302 8-0022: port 0 probe success with role ROLE_MODE_DRP, try_role ROLE_MODE_NONE
[ 1.414640] rk3x-i2c ff3e0000.i2c: Initialized RK3xxx I2C bus at ffffff80097ea000
[ 1.416008] IR NEC protocol handler initialized
[ 1.416060] IR RC5(x/sz) protocol handler initialized
[ 1.416077] IR RC6 protocol handler initialized
[ 1.416094] IR JVC protocol handler initialized
[ 1.416111] IR Sony protocol handler initialized
[ 1.416127] IR SANYO protocol handler initialized
[ 1.416144] IR Sharp protocol handler initialized
[ 1.416161] IR MCE Keyboard/mouse protocol handler initialized
[ 1.416178] IR XMP protocol handler initialized
[ 1.416921] usbcore: registered new interface driver uvcvideo
[ 1.416963] USB Video Class driver (1.1.1)
[ 1.416988] CamSys driver version: v0.48.0, CamSys head file version: v1.0.0
[ 1.423102] test_power_init: could not find dev node
[ 1.427565] rk_tsadcv2_temp_to_code: Invalid conversion table: code=1023, temperature=2147483647
[ 1.427762] rockchip-thermal ff260000.tsadc: tsadc is probed successfully!
[ 1.428296] device-mapper: uevent: version 1.0.3
[ 1.428663] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 1.428801] device-mapper: verity-avb: AVB error handler initialized with vbmeta device:
[ 1.428821] Bluetooth: HCI UART driver ver 2.3
[ 1.428831] Bluetooth: HCI UART protocol H4 registered
[ 1.428839] Bluetooth: HCI UART protocol LL registered
[ 1.428850] rtk_btusb: RTKBT_RELEASE_NAME: 20181126_TV_ANDROID_8.0
[ 1.428863] rtk_btusb: Realtek Bluetooth USB driver module init, version 4.2.1
[ 1.428870] rtk_btusb: Register usb char device interface for BT driver
[ 1.429063] usbcore: registered new interface driver rtk_btusb
[ 1.429519] cpu cpu0: leakage=0
[ 1.442638] cpu cpu0: temp=39375, pvtm=138027 (138257 + -230)
[ 1.443988] cpu cpu0: pvtm-volt-sel=0
[ 1.444591] cpu cpu4: leakage=0
[ 1.457084] cpu cpu4: temp=39375, pvtm=148771 (148913 + -142)
[ 1.457895] cpu cpu4: pvtm-volt-sel=0
[ 1.459771] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[ 1.462383] cpu cpu4: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0
[ 1.464555] sdhci: Secure Digital Host Controller Interface driver
[ 1.464589] sdhci: Copyright(c) Pierre Ossman
[ 1.464609] Synopsys Designware Multimedia Card Interface Driver
[ 1.465856] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.466040] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 1.466081] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 1.466158] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[ 1.466218] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[ 1.466272] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 1.466283] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 1.467540] dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
[ 1.467650] dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
[ 1.467669] dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
[ 1.467724] dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 26,32 bit host data width,256 deep fifo
[ 1.467755] dwmmc_rockchip fe320000.dwmmc: 'clock-freq-min-max' property was deprecated.
[ 1.468148] dwmmc_rockchip fe320000.dwmmc: No vmmc regulator found
[ 1.469264] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[ 1.469602] rockchip-iodomain ff770000.syscon:io-domains: Setting to 3300000 done
[ 1.480698] mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 1.494215] dwmmc_rockchip fe320000.dwmmc: 1 slots initialized
[ 1.495817] sdhci-pltfm: SDHCI platform and OF driver helper
[ 1.497995] sdhci-arasan fe330000.sdhci: No vmmc regulator found
[ 1.498019] sdhci-arasan fe330000.sdhci: No vqmmc regulator found
[ 1.527523] mmc1: SDHCI controller on fe330000.sdhci [fe330000.sdhci] using ADMA
[ 1.531224] hidraw: raw HID events driver (C) Jiri Kosina
[ 1.533930] usbcore: registered new interface driver usbhid
[ 1.534040] usbhid: USB HID core driver
[ 1.534375] inv_mpu_iio: inv_mpu_init:746
[ 1.535601] ashmem: initialized
[ 1.543758] rknandbase v1.2 2018-05-08
[ 1.544842] usbcore: registered new interface driver snd-usb-audio
[ 1.547430] es7243_i2c_probe
[ 1.547711] es7243_start
[ 1.547990] es7243 7-0013: i2c write 0x6 failed
[ 1.548299] es7243 7-0013: i2c write 0x1 failed
[ 1.548426] es7243 7-0013: i2c write 0x2 failed
[ 1.548674] es7243 7-0013: i2c write 0x3 failed
[ 1.548895] es7243 7-0013: i2c write 0x4 failed
[ 1.549116] es7243 7-0013: i2c write 0x5 failed
[ 1.549337] es7243 7-0013: i2c write 0x8 failed
[ 1.549557] es7243 7-0013: i2c write 0x7 failed
[ 1.549778] es7243 7-0013: i2c write 0x9 failed
[ 1.550002] es7243 7-0013: i2c write 0x6 failed
[ 1.550220] es7243 7-0013: i2c write 0x5 failed
[ 1.551657] es7243_i2c_probe finish
[ 1.556387] u32 classifier
[ 1.556409] Actions configured
[ 1.556465] Netfilter messages via NETLINK v0.30.
[ 1.556722] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 1.557393] ctnetlink v0.93: registering with nfnetlink.
[ 1.558445] xt_time: kernel timezone is -0000
[ 1.558689] IPv4 over IPsec tunneling driver
[ 1.559856] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.560150] arp_tables: (C) 2002 David S. Miller
[ 1.560848] Initializing XFRM netlink socket
[ 1.561395] NET: Registered protocol family 10
[ 1.562434] mip6: Mobile IPv6
[ 1.562505] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.564919] sit: IPv6 over IPv4 tunneling driver
[ 1.565834] NET: Registered protocol family 17
[ 1.565915] NET: Registered protocol family 15
[ 1.566123] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[ 1.567545] Bridge firewalling registered
[ 1.567604] Ebtables v2.0 registered
[ 1.568065] Bluetooth: RFCOMM TTY layer initialized
[ 1.568081] Bluetooth: RFCOMM socket layer initialized
[ 1.568108] Bluetooth: RFCOMM ver 1.11
[ 1.568128] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.568136] Bluetooth: BNEP filters: protocol multicast
[ 1.568148] Bluetooth: BNEP socket layer initialized
[ 1.568162] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.568390] Bluetooth: HIDP socket layer initialized
[ 1.568638] l2tp_core: L2TP core driver, V2.0
[ 1.568839] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 1.569055] [WLAN_RFKILL]: Enter rfkill_wlan_init
[ 1.569171] mmc1: MAN_BKOPS_EN bit is not set
[ 1.569632] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[ 1.569738] [WLAN_RFKILL]: can't find rockchip,grf property
[ 1.569954] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8188eu
[ 1.570175] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[ 1.570397] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[ 1.570679] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[ 1.570840] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[ 1.571062] [WLAN_RFKILL]: Exit rfkill_wlan_probe
[ 1.571329] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.571846] sensor_register_slave:mpu6500_gyro,id=49
[ 1.571989] sensor_register_slave:mpu6880_gyro,id=50
[ 1.572621] Error: Driver 'gc0312' is already registered, aborting...
[ 1.572792] Error: Driver 'gc2145' is already registered, aborting...
[ 1.573899] Registered cp15_barrier emulation handler
[ 1.574236] Registered setend emulation handler
[ 1.575257] registered taskstats version 1
[ 1.576764] Key type encrypted registered
[ 1.577360] rockchip ion idev is NULL
[ 1.577380] rga2 ff680000.rga: rga ion client create success!
[ 1.577605] rga: Driver loaded successfully ver:3.02
[ 1.577765] rga2: Module initialized.
[ 1.579218] phy phy-ff770000.syscon:usb2-phy@e450.5: Failed to get VBUS supply regulator
[ 1.580915] phy phy-ff770000.syscon:usb2-phy@e460.7: Failed to get VBUS supply regulator
[ 1.582473] mmc1: new HS400 Enhanced strobe MMC card at address 0001
[ 1.582649] rockchip-drm display-subsystem: dmc is disabled
[ 1.583080] rockchip-vop ff900000.vop: missing rockchip,grf property
[ 1.583217] mmcblk1: mmc1:0001 DF4016 14.7 GiB
[ 1.583495] rockchip-drm display-subsystem: bound ff900000.vop (ops vop_component_ops)
[ 1.583565] rockchip-vop ff8f0000.vop: missing rockchip,grf property
[ 1.583652] mmcblk1boot0: mmc1:0001 DF4016 partition 1 4.00 MiB
[ 1.583850] rockchip-drm display-subsystem: bound ff8f0000.vop (ops vop_component_ops)
[ 1.584179] mmcblk1boot1: mmc1:0001 DF4016 partition 2 4.00 MiB
[ 1.584620] mmcblk1rpmb: mmc1:0001 DF4016 partition 3 4.00 MiB
[ 1.584646] i2c i2c-9: of_i2c: modalias failure on /hdmi@ff940000/ports
[ 1.584700] dwhdmi-rockchip ff940000.hdmi: registered DesignWare HDMI I2C bus driver
[ 1.584856] dwhdmi-rockchip ff940000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[ 1.586621] rockchip-drm display-subsystem: bound ff940000.hdmi (ops dw_hdmi_rockchip_ops)
[ 1.587286] i2c i2c-10: of_i2c: modalias failure on /dp@fec00000/ports
[ 1.588111] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
[ 1.588200] rockchip-drm display-subsystem: bound fec00000.dp (ops cdn_dp_component_ops)
[ 1.588216] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.588225] [drm] No driver support for vblank timestamp query.
[ 1.588582] mmcblk1: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14
[ 1.588663] rockchip-drm display-subsystem: failed to parse loader memory
[ 1.640665] fusb302 8-0022: CC connected in CC1 as UFP
[ 1.643245] cdn-dp fec00000.dp: [drm:cdn_dp_pd_event_work] Not connected. Disabling cdn
[ 1.839615] rockchip-drm display-subsystem: fb0: frame buffer device
[ 1.857277] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
[ 1.857659] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 1
[ 1.857890] xhci-hcd xhci-hcd.11.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06030010
[ 1.857961] xhci-hcd xhci-hcd.11.auto: irq 231, io mem 0xfe800000
[ 1.858252] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.858282] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.858292] usb usb1: Product: xHCI Host Controller
[ 1.858302] usb usb1: Manufacturer: Linux 4.4.167 xhci-hcd
[ 1.858312] usb usb1: SerialNumber: xhci-hcd.11.auto
[ 1.858923] hub 1-0:1.0: USB hub found
[ 1.858984] hub 1-0:1.0: 1 port detected
[ 1.859274] xhci-hcd xhci-hcd.11.auto: xHCI Host Controller
[ 1.859452] xhci-hcd xhci-hcd.11.auto: new USB bus registered, assigned bus number 2
[ 1.859542] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 1.859641] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.859678] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.859689] usb usb2: Product: xHCI Host Controller
[ 1.859698] usb usb2: Manufacturer: Linux 4.4.167 xhci-hcd
[ 1.859708] usb usb2: SerialNumber: xhci-hcd.11.auto
[ 1.860150] hub 2-0:1.0: USB hub found
[ 1.860210] hub 2-0:1.0: 1 port detected
[ 1.861909] xhci-hcd xhci-hcd.11.auto: remove, state 1
[ 1.861967] usb usb2: USB disconnect, device number 1
[ 1.881169] xhci-hcd xhci-hcd.11.auto: Host not halted after 16000 microseconds.
[ 1.881213] xhci-hcd xhci-hcd.11.auto: Host controller not halted, aborting reset.
[ 1.881266] xhci-hcd xhci-hcd.11.auto: USB bus 2 deregistered
[ 1.881449] xhci-hcd xhci-hcd.11.auto: remove, state 1
[ 1.881472] usb usb1: USB disconnect, device number 1
[ 1.882065] xhci-hcd xhci-hcd.11.auto: USB bus 1 deregistered
[ 2.104383] phy phy-ff770000.syscon:usb2-phy@e450.5: charger = USB_SDP_CHARGER
[ 2.109933] rockchip-dwc3 usb0: USB peripheral connected
[ 2.112178] xhci-hcd xhci-hcd.12.auto: xHCI Host Controller
[ 2.112641] xhci-hcd xhci-hcd.12.auto: new USB bus registered, assigned bus number 1
[ 2.113035] xhci-hcd xhci-hcd.12.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x06230010
[ 2.113123] xhci-hcd xhci-hcd.12.auto: irq 232, io mem 0xfe900000
[ 2.113555] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.113590] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.113619] usb usb1: Product: xHCI Host Controller
[ 2.113637] usb usb1: Manufacturer: Linux 4.4.167 xhci-hcd
[ 2.113654] usb usb1: SerialNumber: xhci-hcd.12.auto
[ 2.114803] hub 1-0:1.0: USB hub found
[ 2.115015] hub 1-0:1.0: 1 port detected
[ 2.115719] xhci-hcd xhci-hcd.12.auto: xHCI Host Controller
[ 2.116079] xhci-hcd xhci-hcd.12.auto: new USB bus registered, assigned bus number 2
[ 2.116196] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.116568] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.116641] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.116863] usb usb2: Product: xHCI Host Controller
[ 2.117088] usb usb2: Manufacturer: Linux 4.4.167 xhci-hcd
[ 2.117111] usb usb2: SerialNumber: xhci-hcd.12.auto
[ 2.118092] hub 2-0:1.0: USB hub found
[ 2.118206] hub 2-0:1.0: 1 port detected
[ 2.122579] ehci-platform fe380000.usb: EHCI Host Controller
[ 2.123095] ehci-platform fe380000.usb: new USB bus registered, assigned bus number 3
[ 2.123585] ehci-platform fe380000.usb: irq 28, io mem 0xfe380000
[ 2.130675] ehci-platform fe380000.usb: USB 2.0 started, EHCI 1.00
[ 2.131011] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.131216] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.131472] usb usb3: Product: EHCI Host Controller
[ 2.131694] usb usb3: Manufacturer: Linux 4.4.167 ehci_hcd
[ 2.131922] usb usb3: SerialNumber: fe380000.usb
[ 2.133145] hub 3-0:1.0: USB hub found
[ 2.133250] hub 3-0:1.0: 1 port detected
[ 2.137625] ehci-platform fe3c0000.usb: EHCI Host Controller
[ 2.138827] ehci-platform fe3c0000.usb: new USB bus registered, assigned bus number 4
[ 2.139545] ehci-platform fe3c0000.usb: irq 30, io mem 0xfe3c0000
[ 2.147380] ehci-platform fe3c0000.usb: USB 2.0 started, EHCI 1.00
[ 2.148124] usb usb4: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.148328] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.148487] usb usb4: Product: EHCI Host Controller
[ 2.148712] usb usb4: Manufacturer: Linux 4.4.167 ehci_hcd
[ 2.148935] usb usb4: SerialNumber: fe3c0000.usb
[ 2.150890] hub 4-0:1.0: USB hub found
[ 2.151033] hub 4-0:1.0: 1 port detected
[ 2.153545] ohci-platform fe3a0000.usb: Generic Platform OHCI controller
[ 2.154587] ohci-platform fe3a0000.usb: new USB bus registered, assigned bus number 5
[ 2.155278] ohci-platform fe3a0000.usb: irq 29, io mem 0xfe3a0000
[ 2.168626] vendor storage:20160801 ret = 0
[ 2.211676] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.211794] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.212014] usb usb5: Product: Generic Platform OHCI controller
[ 2.212239] usb usb5: Manufacturer: Linux 4.4.167 ohci_hcd
[ 2.212463] usb usb5: SerialNumber: fe3a0000.usb
[ 2.214418] hub 5-0:1.0: USB hub found
[ 2.214557] hub 5-0:1.0: 1 port detected
[ 2.216545] ohci-platform fe3e0000.usb: Generic Platform OHCI controller
[ 2.217211] ohci-platform fe3e0000.usb: new USB bus registered, assigned bus number 6
[ 2.217918] ohci-platform fe3e0000.usb: irq 31, io mem 0xfe3e0000
[ 2.275334] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 2.275473] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.275687] usb usb6: Product: Generic Platform OHCI controller
[ 2.275910] usb usb6: Manufacturer: Linux 4.4.167 ohci_hcd
[ 2.276133] usb usb6: SerialNumber: fe3e0000.usb
[ 2.278011] hub 6-0:1.0: USB hub found
[ 2.278272] hub 6-0:1.0: 1 port detected
[ 2.281361] dwmmc_rockchip fe310000.dwmmc: IDMAC supports 32-bit address mode.
[ 2.281627] dwmmc_rockchip fe310000.dwmmc: Using internal DMA controller.
[ 2.281726] dwmmc_rockchip fe310000.dwmmc: Version ID is 270a
[ 2.281977] dwmmc_rockchip fe310000.dwmmc: DW MMC controller at irq 25,32 bit host data width,256 deep fifo
[ 2.282205] dwmmc_rockchip fe310000.dwmmc: 'clock-freq-min-max' property was deprecated.
[ 2.282451] dwmmc_rockchip fe310000.dwmmc: No vmmc regulator found
[ 2.282604] dwmmc_rockchip fe310000.dwmmc: No vqmmc regulator found
[ 2.283708] dwmmc_rockchip fe310000.dwmmc: allocated mmc-pwrseq
[ 2.297465] mmc_host mmc2: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual 400000HZ div = 0)
[ 2.310860] dwmmc_rockchip fe310000.dwmmc: 1 slots initialized
[ 2.323643] asoc-simple-card rk809-sound: rk817-hifi <-> ff890000.i2s mapping ok
[ 2.323804] asoc-simple-card rk809-sound: ASoC: no source widget found for MICBIAS1
[ 2.324080] asoc-simple-card rk809-sound: ASoC: Failed to add route MICBIAS1 -> direct -> Mic Jack
[ 2.324299] asoc-simple-card rk809-sound: ASoC: no sink widget found for IN1P
[ 2.324521] asoc-simple-card rk809-sound: ASoC: Failed to add route Mic Jack -> direct -> IN1P
[ 2.324747] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOL
[ 2.324972] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOL -> direct -> Headphone Jack
[ 2.325197] asoc-simple-card rk809-sound: ASoC: no source widget found for HPOR
[ 2.325422] asoc-simple-card rk809-sound: ASoC: Failed to add route HPOR -> direct -> Headphone Jack
[ 2.329891] rk-hdmi-dp-sound hdmi-dp-sound: control 3:0:0:ELD:0 is already present
[ 2.329996] hdmi-audio-codec hdmi-audio-codec.10.auto: ASoC: Failed to add ELD: -16
[ 2.330965] rk-hdmi-dp-sound hdmi-dp-sound: multicodec <-> ff8a0000.i2s mapping ok
[ 2.331110] hdmi-audio-codec hdmi-audio-codec.10.auto: ASoC: Failed to create Playback debugfs file
[ 2.334126] mmc_host mmc2: Bus speed (slot 0) = 300000Hz (slot req 300000Hz, actual 300000HZ div = 0)
[ 2.338482] rk808-rtc rk808-rtc: setting system clock to 2017-08-05 09:01:40 UTC (1501923700)
[ 2.340066] It doesn't contain Rogue gpu
[ 2.373534] rockchip_headset_probe() headset have hook adc mode
[ 2.374154] input: rk_headset as /devices/platform/rk_headset/input/input1
[ 2.374212] mmc_host mmc2: Bus speed (slot 0) = 200000Hz (slot req 200000Hz, actual 200000HZ div = 0)
[ 2.376076] sound/soc/codecs/rk3399_msm261s4030h0_codec.c,rockchip_msm261s4030h0_card_audio_probe
[ 2.376135] ---------------------rockchip_pcm_card_audio_probe-------------------
[ 2.376383] rockchip_msm261s4030h0_audio_probe---------------110
[ 2.377339] rockchip-msm261s4030h0 rockchip-msm261s4030h0: rockchip-msm261s4030h0-card-hifi <-> ff880000.i2s mapping ok
[ 2.379774] rockchip-msm261s4030h0 rockchip-msm261s4030h0: snd_soc_register_card successful
[ 2.380946] I : [File] : drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 417; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '00:47:39', on 'Jan 19 2019'.
[ 2.381909] Mali: Mali device driver loaded
[ 2.382862] input: rk29-keypad as /devices/platform/rockchip-key/input/input2
[ 2.384690] ALSA device list:
[ 2.384778] #0: rockchip,rk809-codec
[ 2.384795] #1: rk-hdmi-dp-sound
[ 2.384810] #2: RK_msm261s4030h0
[ 2.385631] Freeing unused kernel memory: 768K
[ 2.393047] init: init first stage started!
[ 2.393193] init: First stage mount skipped (recovery mode)
[ 2.393723] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 2.394062] init: Skipped setting INIT_AVB_VERSION (not vbmeta compatible)
[ 2.394226] init: Loading SELinux policy
[ 2.437362] usb 3-1: new high-speed USB device number 2 using ehci-platform
[ 2.493784] audit: type=1403 audit(1501923700.650:2): policy loaded auid=4294967295 ses=4294967295
[ 2.494201] selinux: SELinux: Loaded policy from /sepolicy
[ 2.494201]
[ 2.497110] selinux: SELinux: Loaded file_contexts
[ 2.497110]
[ 2.498390] random: init: uninitialized urandom read (40 bytes read, 52 bits of entropy available)
[ 2.499517] init: init second stage started!
[ 2.503870] init: Using Android DT directory /proc/device-tree/firmware/android/
[ 2.504471] init: Set boot.mode to emmc
[ 2.504516] init: property_set("ro.boot.mode", "emmc") failed: property already set
[ 2.506784] selinux: SELinux: Loaded file_contexts
[ 2.506784]
[ 2.507468] selinux: SELinux: Loaded property_contexts from /plat_property_contexts & /nonplat_property_contexts.
[ 2.507468]
[ 2.507513] init: Running restorecon...
[ 2.510595] selinux: SELinux: Could not stat /dev/block: No such file or directory.
[ 2.510595]
[ 2.511035] init: waitid failed: No child processes
[ 2.511115] init: Couldn't load property file: Unable to open '/system/etc/prop.default': No such file or directory: No such file or directory
[ 2.511753] init: property_set("ro.product.first_api_level", "26") failed: property already set
[ 2.511818] init: property_set("ro.board.platform", "rk3399pro") failed: property already set
[ 2.512428] init: property_set("ro.target.product", "tablet") failed: property already set
[ 2.512483] init: Couldn't load property file: Unable to open '/odm/default.prop': No such file or directory: No such file or directory
[ 2.512516] init: Couldn't load property file: Unable to open '/vendor/default.prop': No such file or directory: No such file or directory
[ 2.513109] init: Created socket '/dev/socket/property_service', mode 666, user 0, group 0
[ 2.513311] init: Parsing file /init.rc...
[ 2.513424] init: Added '/init.bootmode.emmc.rc' to import list
[ 2.513465] init: Added '/init.recovery.rk30board.rc' to import list
[ 2.513485] init: Added '/init.rk30board.usb.rc' to import list
[ 2.513501] init: Added '/init.usb.configfs.rc' to import list
[ 2.513834] init: Parsing file /init.bootmode.emmc.rc...
[ 2.513879] init: Unable to open '/init.bootmode.emmc.rc': No such file or directory
[ 2.513902] init: /init.rc: 1: Could not import file '/init.bootmode.emmc.rc': No such file or directory
[ 2.513923] init: Parsing file /init.recovery.rk30board.rc...
[ 2.513949] init: Unable to open '/init.recovery.rk30board.rc': No such file or directory
[ 2.514000] init: /init.rc: 2: Could not import file '/init.recovery.rk30board.rc': No such file or directory
[ 2.514023] init: Parsing file /init.rk30board.usb.rc...
[ 2.514377] init: Parsing file /init.usb.configfs.rc...
[ 2.515098] init: Parsing file /system/etc/init...
[ 2.515142] init: Unable to open '/system/etc/init': No such file or directory
[ 2.515167] init: Parsing file /vendor/etc/init...
[ 2.515194] init: Unable to open '/vendor/etc/init': No such file or directory
[ 2.515220] init: Parsing file /odm/etc/init...
[ 2.515250] init: Unable to open '/odm/etc/init': No such file or directory
[ 2.515335] init: processing action (early-init) from (/init.rc:6)
[ 2.515445] init: starting service 'ueventd'...
[ 2.516076] audit: type=1400 audit(1501923700.673:3): avc: denied { create } for pid=1 comm="init" name="cgroup.procs" scontext=u:r:init:s0 tcontext=ubject_r:rootfs:s0 tclass=file permissive=1
[ 2.516137] audit: type=1400 audit(1501923700.673:4): avc: denied { write } for pid=1 comm="init" path="/acct/uid_0/pid_193/cgroup.procs" dev="rootfs" ino=2157 scontext=u:r:init:s0 tcontext=ubject_r:rootfs:s0 tclass=file permissive=1
[ 2.516465] init: processing action (wait_for_coldboot_done) from (<Builtin Action>:0)
[ 2.518248] random: ueventd: uninitialized urandom read (40 bytes read, 52 bits of entropy available)
[ 2.521077] ueventd: ueventd started!
[ 2.521269] ueventd: Parsing file /ueventd.rc...
[ 2.522862] ueventd: Parsing file /vendor/ueventd.rc...
[ 2.522992] ueventd: Unable to open '/vendor/ueventd.rc': No such file or directory
[ 2.523057] ueventd: Parsing file /odm/ueventd.rc...
[ 2.523172] ueventd: Unable to open '/odm/ueventd.rc': No such file or directory
[ 2.523367] ueventd: Parsing file /ueventd.rk30board.rc...
[ 2.524275] ueventd: /ueventd.rk30board.rc: 56: invalid gid 'net_bt_stack'
[ 2.524368] ueventd: /ueventd.rk30board.rc: 57: invalid gid 'net_bt_stack'
[ 2.524465] ueventd: /ueventd.rk30board.rc: 58: invalid gid 'net_bt_stack'
[ 2.524520] ueventd: /ueventd.rk30board.rc: 60: invalid gid 'net_bt_stack'
[ 2.524900] ueventd: /ueventd.rk30board.rc: 114: invalid gid 'trace'
[ 2.530428] selinux: SELinux: Loaded file_contexts
[ 2.530428]
[ 2.561060] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.561772] usb 3-1: New USB device found, idVendor=0bda, idProduct=d723
[ 2.561787] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 2.561795] usb 3-1: Product: 802.11n WLAN Adapter
[ 2.561802] usb 3-1: Manufacturer: Realtek
[ 2.561809] usb 3-1: SerialNumber: 00e04c000001
[ 2.563024] rtk_btusb: btusb_probe: usb_interface ffffffc078546000, bInterfaceNumber 0, idVendor 0x0bda, idProduct 0x0000
[ 2.563038] rtk_btusb: get_fw_table_entry: Product id = 0xd723, fw table entry size 50
[ 2.563047] rtk_btusb: firmware_info_init: Auto suspend is disabled
[ 2.563061] rtk_btusb: btusb_probe: Check bt reset flag 0
[ 2.578127] usb 2-1: New USB device found, idVendor=05e3, idProduct=0616
[ 2.578154] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.578163] usb 2-1: Product: USB3.0 Hub
[ 2.578171] usb 2-1: Manufacturer: GenesysLogic
[ 2.580949] hub 2-1:1.0: USB hub found
[ 2.581382] hub 2-1:1.0: 4 ports detected
[ 2.680757] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 2.707512] selinux: SELinux: Loaded file_contexts
[ 2.707512]
[ 2.747048] ueventd: Coldboot took 0.216 seconds
[ 2.750925] init: Command 'wait_for_coldboot_done' action=wait_for_coldboot_done (<Builtin Action>:0) returned 0 took 234ms.
[ 2.751018] init: processing action (mix_hwrng_into_linux_rng) from (<Builtin Action>:0)
[ 2.751073] init: /dev/hw_random not found
[ 2.751146] init: processing action (set_mmap_rnd_bits) from (<Builtin Action>:0)
[ 2.751852] init: processing action (set_kptr_restrict) from (<Builtin Action>:0)
[ 2.752088] init: processing action (keychord_init) from (<Builtin Action>:0)
[ 2.752155] init: processing action (console_init) from (<Builtin Action>:0)
[ 2.752207] init: processing action (init) from (/init.rc:12)
[ 2.754944] init: processing action (mix_hwrng_into_linux_rng) from (<Builtin Action>:0)
[ 2.754992] init: /dev/hw_random not found
[ 2.755034] init: processing action (late-init) from (/init.rc:58)
[ 2.755094] init: processing action (queue_property_triggers) from (<Builtin Action>:0)
[ 2.755153] init: processing action (load_system_props_action) from (/init.rc:51)
[ 2.755198] init: Couldn't load property file: Unable to open '/system/build.prop': No such file or directory: No such file or directory
[ 2.755231] init: Couldn't load property file: Unable to open '/odm/build.prop': No such file or directory: No such file or directory
[ 2.755267] init: Couldn't load property file: Unable to open '/vendor/build.prop': No such file or directory: No such file or directory
[ 2.755299] init: Couldn't load property file: Unable to open '/factory/factory.prop': No such file or directory: No such file or directory
[ 2.763137] init: processing action (firmware_mounts_complete) from (/init.rc:54)
[ 2.763398] init: processing action (persist.sys.usb.config=* && boot) from (/init.rc:36)
[ 2.763629] init: processing action (boot) from (/init.rc:43)
[ 2.764947] init: starting service 'charger'...
[ 2.766515] init: starting service 'recovery'...
[ 2.768223] init: processing action (boot) from (/init.rk30board.usb.rc:1)
[ 2.769344] random: recovery: uninitialized urandom read (40 bytes read, 60 bits of entropy available)
[ 2.769369] random: charger: uninitialized urandom read (40 bytes read, 60 bits of entropy available)
Starting recovery (pid 203) on Sat Aug 5 09:01:40 2017
[ 2.773158] healthd: No battery devices found
[ 2.773513] healthd: battery l=100 v=0 t=42.4 h=2 st=2 chg=a
recovery filesystem table
=========================
0 /system ext4 /dev/block/by-name/system 0
1 /vendor ext4 /dev/block/by-name/vendor 0
2 /mnt/internal_sd vfat /dev/block/platform/fe330000.sdhci/by-name/user 0
3 /mnt/external_sd vfat /dev/block/mmcblk0p1 0
4 /system ext4 /dev/block/by-name/system 0
5 /vendor ext4 /dev/block/by-name/vendor 0
6 /oem ext4 /dev/block/by-name/oem 0
7 /cache ext4 /dev/block/by-name/cache 0
8 /metadata ext4 /dev/block/by-name/metadata 0
9 /data f2fs /dev/block/by-name/userdata 0
10 /cust ext4 /dev/block/by-name/cust 0
11 /custom ext4 /dev/block/by-name/custom 0
12 /radical_update ext4 /dev/block/by-name/radical_update 0
13 /misc emmc /dev/block/by-name/misc 0
14 /uboot emmc /dev/block/by-name/uboot 0
15 /charge emmc /dev/block/by-name/charge 0
16 /resource emmc /dev/block/by-name/resource 0
17 /parameter emmc /dev/block/by-name/parameter 0
18 /boot emmc /dev/block/by-name/boot 0
19 /recovery emmc /dev/block/by-name/recovery 0
20 /backup emmc /dev/block/by-name/backup 0
21 /trust emmc /dev/block/by-name/trust 0
22 /baseparamer emmc /dev/block/by-name/baseparamer 0
23 /frp emmc /dev/block/by-name/frp 0
24 /tmp ramdisk ramdisk 0
# emmc_point is /dev/block/mmcblk1
sd_point is (null)
sd_point_2 is (null)
read cmdline
[ 2.775751] file system registered
[ 2.776587] using random self ethernet address
[ 2.776604] using random host ethernet address
[ 2.776723] init: Unable to open '/config/usb_gadget/g1/functions/rndis.gs4/wceis':I:Boot command: boot-recovery Pe
I:Got 2 arguments from boot messarmge
ission denied
[ 2.778172] init: processing action (enable_property_trigger) from (<Builtin Action>:0)
[ 2.778338] init: processing action (ro.debuggable=1) from (/init.rc:92)
[ 2.778385] init: starting service 'adbd'...
[ 2.779298] audit: type=1400 audit(1501923700.936:5): avc: granted { read } for pid=1 comm="init" name="ttyFIQ0" dev="tmpfs" ino=245 scontext=u:r:init:s0 tcontext=ubject_r:serial_device:s0 tclass=chr_file
[ 2.779359] audit: type=1400 audit(1501923700.936:6): avc: granted { read open } for pid=1 comm="init" path="/dev/ttyFIQ0" dev="tmpfs" ino=245 scontext=u:r:init:s0 tcontext=ubject_r:serial_device:s0 tclass=chr_file
[ 2.779479] init: starting service 'console'...
[ 2.780052] init: Created socket '/dev/socket/adbd', mode 660, user 1000, group 1000
[ 2.780422] init: processing action (sys.usb.config=mtp,adb && sys.usb.configfs=1) from (/init.rk30board.usb.rc:43)
[ 2.780696] init: processing action (sys.usb.config=mtp,adb && sys.usb.configfs=1) from (/init.usb.configfs.rc:33)
[ 2.780772] init: processing action (sys.usb.config=mtp,adb && sys.usb.configfs=1 && sys.usb.ffs.mtp.ready=1 && sys.usb.ffs.ready=1) from (/init.usb.configfs.rc:37)
[ 2.780871] audit: type=1400 audit(1501923700.940:7): avc: granted { read } for pid=206 comm="init" name="ttyFIQ0" dev="tmpfs" ino=245 scontext=u:r:init:s0 tcontext=ubject_r:serial_device:s0 tclass=chr_file
[ 2.780922] audit: type=1400 audit(1501923700.940:8): avc: granted { read open } for pid=206 comm="init" path="/dev/ttyFIQ0" dev="tmpfs" ino=245 scontext=u:r:init:s0 tcontext=ubject_r:serial_device:s0 tclass=chr_file
[ 2.781085] initlocale is [en-US]
stage is []
reason is [(null)]
W:Failed to read max brightness: No such file or directory
I:Screensaver disabled
: setpgid failed for console: Operation not permitted
[ 2.781143] configfs-gadget gadget: unbind function 'mtp'/ffffffc07ba4b000
[ 2.781177] configfs-gadget fe800000.dwc3: failed to start g1: -19
[ 2.781226] init: Unable to write to '/config/usb_gadget/g1/UDC': No such device
[ 2.781569] audit: type=1400 audit(1501923700.940:9): avc: denied { entrypoint } for pid=206 comm="init" path="/sbin/sh" dev="rootfs" ino=10091 scontext=u:r:shell:s0 tcontext=ubject_r:rootfs:s0 tclass=file permissive=1
[ 2.781949] random: adbd: uninitialized urandom read (40 bytes read, 61 bits of entropy available)
[ 2.782511] audit: type=1400 audit(1501923700.940:10): avc: denied { read } for pid=206 comm="sh" path="/sbin/sh" dev="rootfs" ino=10091 scontext=u:r:shell:s0 tcontext=ubject_r:rootfs:s0 tclass=file permissive=1
[ 2.785437] read descriptors
[ 2.785541] read strings
[ 2.786886] init: processing action (sys.usb.config=mtp,adb && sys.usb.configfs=1 && sys.usb.ffs.mtp.ready=1 && sys.usb.ffs.ready=1) from (/init.usb.configfs.rc:37)
[ 2.797595] EXT4-fs (mmcblk1p8): mounted filesystem with ordered data mode. Opts: (null)
[ 2.814986] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610
[ 2.815027] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.815046] usb 1-1: Product: USB2.0 Hub
[ 2.815063] usb 1-1: Manufacturer: GenesysLogic
[ 2.821016] hub 1-1:1.0: USB hub found
[ 2.821937] hub 1-1:1.0: 4 ports detected
[ 3.038309] android_work: did not send uevent (0 0 (null))
[ 3.118152] android_work: sent uevent USB_STATE=CONNECTED
[ 3.122881] configfs-gadget gadget: high-speed config #1: b
[ 3.123255] android_work: sent uevent USB_STATE=CONFIGURED
[ 3.553129] rockchip-vop ff900000.vop: [drm:vop_crtc_enable] Update mode to 2880x1620p50, type: 11
[ 3.576145] dwhdmi-rockchip ff940000.hdmi: Rate 253130000 missing; compute N dynamically
erasing_text: en-US (68 x 29 @ 900)
no_command_text: en-US (124 x 29 @ 900)
error_text: en-US (49 x 29 @ 900)
[ 3.923341] usb 1-1-port2: Cannot enable. Maybe the USB cable is bad?
installing_text: en-US (228 x 29 @ 900)
SELinux: Loaded file_contexts
[ 3.965565] EXT4-fs (mmcblk1p10): mounted filesystem with ordered data mode. Opts: (null)
Command: "/sbin/recovery" "--wipe_all" |
|