Toybrick

楼主: 008kai

TB-RK3399ProD optee---找不到tee的驱动结点/dev/tee0和/dev/teepriv0

zhangzj

超级版主

积分
1117
21#
发表于 2022-2-18 08:57:59 | 只看该作者
008kai 发表于 2022-2-17 20:29
我将optee os中的plat-rockchip/conf.mk文件做出如下修改:

ifeq ($(PLATFORM_FLAVOR),rk3399)

log
回复

使用道具 举报

008kai

注册会员

积分
115
22#
 楼主| 发表于 2022-2-18 11:17:58 | 只看该作者

下面是输出的log信息:无法进入系统

find part:uboot OK. first_lba:0x2000.
find part:trust OK. first_lba:0x4000.
LoadTrust Addr:0x4000
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xf491c
RunBL31 0x40000
NOTICE:  BL31: v2.6(release):v2.6-391-gb22f18e36-dirty
NOTICE:  BL31: Built : 20:08:06, Feb 17 2022
INFO:    GICv3 with legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    Maximum SPI INTID supported: 287
INFO:    plat_rockchip_pmu_init(1625): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
D/TC:0   get_aslr_seed:1376 Bad fdt: -9
D/TC:0   plat_get_aslr_seed:109 Warning: no ASLR seed
D/TC:0   add_phys_mem:572 TEE_SHMEM_START type NSEC_SHM 0x0a400000 size 0x00400000
D/TC:0   add_phys_mem:572 TA_RAM_START type TA_RAM 0x08600000 size 0x01e00000
D/TC:0   add_phys_mem:572 VCORE_UNPG_RW_PA type TEE_RAM_RW 0x08461000 size 0x0019f000
D/TC:0   add_phys_mem:572 VCORE_UNPG_RX_PA type TEE_RAM_RX 0x08400000 size 0x00061000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x06E00000), CORE_MMU_PGDIR_SIZE) type IO_SEC 0xfee00000 size 0x00200000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x071A0000), CORE_MMU_PGDIR_SIZE) type IO_NSEC 0xff000000 size 0x00200000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x07330000), CORE_MMU_PGDIR_SIZE) type IO_SEC 0xff200000 size 0x00200000
D/TC:0   add_va_space:611 type RES_VASPACE size 0x00a00000
D/TC:0   add_va_space:611 type SHM_VASPACE size 0x02000000
D/TC:0   dump_mmap_table:729 type TEE_RAM_RX   va 0x08400000..0x08460fff pa 0x08400000..0x08460fff size 0x00061000 (smallpg)
D/TC:0   dump_mmap_table:729 type TEE_RAM_RW   va 0x08461000..0x085fffff pa 0x08461000..0x085fffff size 0x0019f000 (smallpg)
D/TC:0   dump_mmap_table:729 type SHM_VASPACE  va 0x08600000..0x0a5fffff pa 0x00000000..0x01ffffff size 0x02000000 (pgdir)
D/TC:0   dump_mmap_table:729 type RES_VASPACE  va 0x0a600000..0x0affffff pa 0x00000000..0x009fffff size 0x00a00000 (pgdir)
D/TC:0   dump_mmap_table:729 type TA_RAM       va 0x0b000000..0x0cdfffff pa 0x08600000..0x0a3fffff size 0x01e00000 (pgdir)
D/TC:0   dump_mmap_table:729 type NSEC_SHM     va 0x0ce00000..0x0d1fffff pa 0x0a400000..0x0a7fffff size 0x00400000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_SEC       va 0x0d200000..0x0d3fffff pa 0xfee00000..0xfeffffff size 0x00200000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_NSEC      va 0x0d400000..0x0d5fffff pa 0xff000000..0xff1fffff size 0x00200000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_SEC       va 0x0d600000..0x0d7fffff pa 0xff200000..0xff3fffff size 0x00200000 (pgdir)
D/TC:0   core_mmu_xlat_table_alloc:494 xlat tables used 1 / 5
D/TC:0   core_mmu_xlat_table_alloc:494 xlat tables used 2 / 5
I/TC:
I/TC: No non-secure external DT
D/TC:0 0 get_console_node_from_dt:70 No console directive from DTB
I/TC: OP-TEE version: 3.11.0-777-g169eac19-dev (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #2 Fri Feb 18 03:14:40 UTC 2022 aarch64
I/TC: Primary CPU initializing
D/TC:0 0 boot_init_primary_late:1257 Executing at offset 0 with virtual load address 0x8400000
D/TC:0 0 call_preinitcalls:21 level 2 mobj_mapped_shm_init()
D/TC:0 0 mobj_mapped_shm_init:449 Shared memory address range: 8600000, a600000
D/TC:0 0 call_initcalls:40 level 1 register_time_source()
D/TC:0 0 call_initcalls:40 level 1 teecore_init_pub_ram()
D/TC:0 0 call_initcalls:40 level 3 platform_init()
D/TC:0 0 platform_secure_ddr_region:35 protecting region 1: 0x8400000-0xa400000
D/TC:0 0 call_initcalls:40 level 3 check_ta_store()
D/TC:0 0 check_ta_store:408 TA store: "Secure Storage TA"
D/TC:0 0 check_ta_store:408 TA store: "REE"
D/TC:0 0 call_initcalls:40 level 3 verify_pseudo_tas_conformance()
D/TC:0 0 call_initcalls:40 level 3 tee_cryp_init()
D/TC:0 0 call_initcalls:40 level 4 tee_fs_init_key_manager()
D/TC:0 0 call_initcalls:40 level 6 dt_driver_release_provider()
D/TC:0 0 call_initcalls:40 level 6 mobj_init()
D/TC:0 0 call_initcalls:40 level 6 default_mobj_init()
D/TC:0 0 call_finalcalls:59 level 1 release_external_dt()
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Initializing BL32 success!!
INFO:    bl31_prepare_next_image_entry
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09 (Feb 18 2022 - 10:00:44 +0800)

Model: Rockchip RK3399 Evaluation Board
PreSerial: 2
DRAM:  3.9 GiB
Sysmem: init
Relocation Offset is: f5bd0000
Using default environment

dwmmc@fe320000: 1, sdhci@fe330000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 150Mhz
PartType: EFI
rockchip_get_boot_mode: Could not found misc partition
boot mode: normal
init_resource_list: failed to get boot part, ret=-1
init_resource_list: failed to get resource part, ret=-1
Distro DTB: /extlinux/toybrick.dtb
105926 bytes read in 51 ms (2 MiB/s)
I2c0 speed: 400000Hz
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_center 900000 uV
vdd_cpu_l 900000 uV
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
TEEC: malloc init fail!
TEEC: OpteeClientMemInit fail!
toybrick_SnMacAc_check read sn_mac_ac fail
toybrick_SnMacAc_check write rpmb
TEEC: malloc init fail!
TEEC: OpteeClientMemInit fail!
toybrick_SnMacAc_check trusty_write_toybrick_SnMacAc wrong!
RKUSB: LUN 0, dev 0, hwpart 0, sector 0x0, count 0x3a3e000
回复

使用道具 举报

008kai

注册会员

积分
115
23#
 楼主| 发表于 2022-2-21 11:12:09 | 只看该作者

从打印的log来看,应该改是u-boot/lib/optee_client_Api中的代码出现了问题,u-boot中的关于optee client的这部分代码需要去掉嘛?
回复

使用道具 举报

zhangzj

超级版主

积分
1117
24#
发表于 2022-2-22 08:47:26 | 只看该作者
008kai 发表于 2022-2-21 11:12
从打印的log来看,应该改是u-boot/lib/optee_client_Api中的代码出现了问题,u-boot中的关于optee client ...

可以去掉,因为client和optee os版本不匹配了。
1. 把uboot中optee相关的宏disable掉
CONFIG_OPTEE_CLIENT=y
CONFIG_OPTEE_V1=y
2. 把依赖optee client的这个代码去掉
arch/arm/mach-rockchip/boot_mode.c
toybrick_check_SnMacAc();
回复

使用道具 举报

008kai

注册会员

积分
115
25#
 楼主| 发表于 2022-2-22 11:19:48 | 只看该作者
zhangzj 发表于 2022-2-22 08:47
可以去掉,因为client和optee os版本不匹配了。
1. 把uboot中optee相关的宏disable掉
CONFIG_OPTEE_CLIEN ...

按照您所说的做出对应修改,即把把uboot中optee相关的宏disable掉,然后将arch/arm/mach-rockchip/boot_mode.c 中的toybrick_SnMacAc_check()函数中的内容注释掉,编译u-boot时报错:
common/built-in.o: In function `android_bootloader_boot_flow':
/home/hyy/rk3399pro_optee/u-boot/common/android_bootloader.c:1123: undefined reference to `trusty_read_vbootkey_enable_flag'
drivers/usb/gadget/built-in.o: In function `rkusb_do_vs_write':
/home/hyy/rk3399pro_optee/u-boot/drivers/usb/gadget/f_rockusb.c:387: undefined reference to `trusty_write_toybrick_seed'
drivers/usb/gadget/built-in.o: In function `rkusb_do_vs_read':
/home/hyy/rk3399pro_optee/u-boot/drivers/usb/gadget/f_rockusb.c:514: undefined reference to `trusty_read_toybrick_cpu_id'
/home/hyy/rk3399pro_optee/u-boot/drivers/usb/gadget/f_rockusb.c:530: undefined reference to `trusty_read_toybrick_cpu_id'
Segmentation fault (core dumped)
make: *** [Makefile:1276: u-boot] Error 139

似乎还有其他文件依赖optee client,我将上述显示未定义的函数在对应的文件中全部注释掉,u-boot编译通过,我将生成的u-boot.img烧写进开发板,发现此时开发板移植不断重启,打印log如下:
atags_set_bootdev: ret0)
GPT part:  0, name:            uboot, start:0x2000, size:0x2000
GPT part:  1, name:            trust, start:0x4000, size:0x2000
GPT part:  2, name:       boot_linux, start:0x6000, size:0x30000
GPT part:  3, name:           rootfs, start:0x36000, size:0x3a07fdf
find part:uboot OK. first_lba:0x2000.
find part:trust OK. first_lba:0x4000.
LoadTrust Addr:0x4000
No find bl30.bin
Load uboot, ReadLba = 2000
Load OK, addr=0x200000, size=0xeb59c
RunBL31 0x40000
NOTICE:  BL31: v2.6(release):v2.6-391-gb22f18e36-dirty
NOTICE:  BL31: Built : 20:08:06, Feb 17 2022
INFO:    GICv3 with legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    Maximum SPI INTID supported: 287
INFO:    plat_rockchip_pmu_init(1625): pd status 3e
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
D/TC:0   get_aslr_seed:1376 Bad fdt: -9
D/TC:0   plat_get_aslr_seed:109 Warning: no ASLR seed
D/TC:0   add_phys_mem:572 TEE_SHMEM_START type NSEC_SHM 0x0a400000 size 0x00400000
D/TC:0   add_phys_mem:572 TA_RAM_START type TA_RAM 0x08600000 size 0x01e00000
D/TC:0   add_phys_mem:572 VCORE_UNPG_RW_PA type TEE_RAM_RW 0x08461000 size 0x0019f000
D/TC:0   add_phys_mem:572 VCORE_UNPG_RX_PA type TEE_RAM_RX 0x08400000 size 0x00061000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x06E00000), CORE_MMU_PGDIR_SIZE) type IO_SEC 0xfee00000 size 0x00200000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x071A0000), CORE_MMU_PGDIR_SIZE) type IO_NSEC 0xff000000 size 0x00200000
D/TC:0   add_phys_mem:572 ROUNDDOWN((0xF8000000 + 0x07330000), CORE_MMU_PGDIR_SIZE) type IO_SEC 0xff200000 size 0x00200000
D/TC:0   add_va_space:611 type RES_VASPACE size 0x00a00000
D/TC:0   add_va_space:611 type SHM_VASPACE size 0x02000000
D/TC:0   dump_mmap_table:729 type TEE_RAM_RX   va 0x08400000..0x08460fff pa 0x08400000..0x08460fff size 0x00061000 (smallpg)
D/TC:0   dump_mmap_table:729 type TEE_RAM_RW   va 0x08461000..0x085fffff pa 0x08461000..0x085fffff size 0x0019f000 (smallpg)
D/TC:0   dump_mmap_table:729 type SHM_VASPACE  va 0x08600000..0x0a5fffff pa 0x00000000..0x01ffffff size 0x02000000 (pgdir)
D/TC:0   dump_mmap_table:729 type RES_VASPACE  va 0x0a600000..0x0affffff pa 0x00000000..0x009fffff size 0x00a00000 (pgdir)
D/TC:0   dump_mmap_table:729 type TA_RAM       va 0x0b000000..0x0cdfffff pa 0x08600000..0x0a3fffff size 0x01e00000 (pgdir)
D/TC:0   dump_mmap_table:729 type NSEC_SHM     va 0x0ce00000..0x0d1fffff pa 0x0a400000..0x0a7fffff size 0x00400000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_SEC       va 0x0d200000..0x0d3fffff pa 0xfee00000..0xfeffffff size 0x00200000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_NSEC      va 0x0d400000..0x0d5fffff pa 0xff000000..0xff1fffff size 0x00200000 (pgdir)
D/TC:0   dump_mmap_table:729 type IO_SEC       va 0x0d600000..0x0d7fffff pa 0xff200000..0xff3fffff size 0x00200000 (pgdir)
D/TC:0   core_mmu_xlat_table_alloc:494 xlat tables used 1 / 5
D/TC:0   core_mmu_xlat_table_alloc:494 xlat tables used 2 / 5
I/TC:
I/TC: No non-secure external DT
D/TC:0 0 get_console_node_from_dt:70 No console directive from DTB
I/TC: OP-TEE version: 3.11.0-777-g169eac19-dev (gcc version 6.3.1 20170404 (Linaro GCC 6.3-2017.05)) #4 Mon Feb 21 03:00:48 UTC 2022 aarch64
I/TC: Primary CPU initializing
D/TC:0 0 boot_init_primary_late:1257 Executing at offset 0 with virtual load address 0x8400000
D/TC:0 0 call_preinitcalls:21 level 2 mobj_mapped_shm_init()
D/TC:0 0 mobj_mapped_shm_init:449 Shared memory address range: 8600000, a600000
D/TC:0 0 call_initcalls:40 level 1 register_time_source()
D/TC:0 0 call_initcalls:40 level 1 teecore_init_pub_ram()
D/TC:0 0 call_initcalls:40 level 3 platform_init()
D/TC:0 0 platform_secure_ddr_region:35 protecting region 1: 0x8400000-0xa400000
D/TC:0 0 call_initcalls:40 level 3 check_ta_store()
D/TC:0 0 check_ta_store:408 TA store: "Secure Storage TA"
D/TC:0 0 check_ta_store:408 TA store: "REE"
D/TC:0 0 call_initcalls:40 level 3 verify_pseudo_tas_conformance()
D/TC:0 0 call_initcalls:40 level 3 tee_cryp_init()
D/TC:0 0 call_initcalls:40 level 4 tee_fs_init_key_manager()
D/TC:0 0 call_initcalls:40 level 6 dt_driver_release_provider()
D/TC:0 0 call_initcalls:40 level 6 mobj_init()
D/TC:0 0 call_initcalls:40 level 6 default_mobj_init()
D/TC:0 0 call_finalcalls:59 level 1 release_external_dt()
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Initializing BL32 success!!
INFO:    bl31_prepare_next_image_entry
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0x200000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-g22af63bad7-dirty (Feb 22 2022 - 11:09:20 +0800)

Model: Rockchip RK3399 Evaluation Board
PreSerial: 2
DRAM:  3.9 GiB
Sysmem: init
Relocation Offset is: f5bda000
Using default environment

dwmmc@fe320000: 1, sdhci@fe330000: 0
Bootdev(atags): mmc 0
MMC0: HS400, 150Mhz
PartType: EFI
rockchip_get_boot_mode: Could not found misc partition
boot mode: normal
init_resource_list: failed to get boot part, ret=-1
init_resource_list: failed to get resource part, ret=-1
Distro DTB: /extlinux/toybrick.dtb
106116 bytes read in 51 ms (2 MiB/s)
I2c0 speed: 400000Hz
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_center 900000 uV
vdd_cpu_l 900000 uV
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
Warn: can't find connect driver
Warn: can't find connect driver
Failed to found available display route
CLK: (uboot. arml: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
CLK: (uboot. armb: enter 24000 KHz, init 24000 KHz, kernel 0N/A)
  aplll 816000 KHz
  apllb 24000 KHz
  dpll 800000 KHz
  cpll 24000 KHz
  gpll 800000 KHz
  npll 600000 KHz
  vpll 24000 KHz
  aclk_perihp 133333 KHz
  hclk_perihp 66666 KHz
  pclk_perihp 33333 KHz
  aclk_perilp0 266666 KHz
  hclk_perilp0 88888 KHz
  pclk_perilp0 44444 KHz
  hclk_perilp1 100000 KHz
  pclk_perilp1 50000 KHz
Net:   eth0: ethernet@fe300000
Hit key to stop autoboot('CTRL+C'):  0
Could not find misc partition
ANDROID: reboot reason: "(none)"
Not AVB images, AVB skip
load_android_image: Can't find part: boot
Android image load failed
Android boot failed, error -1.
do_boot_rockchip: Could not find rootfs part
Card did not respond to voltage select!
mmc_init: -95, time 9
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:3...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
237 bytes read in 54 ms (3.9 KiB/s)
1:      rockchip-kernel-4.4
Retrieving file: /initramfs-toybrick-2.0.img
16096158 bytes read in 177 ms (86.7 MiB/s)
Retrieving file: /extlinux/Image
20918280 bytes read in 226 ms (88.3 MiB/s)
append: earlycon=uart8250,mmio32,0xff1a0000 initrd=/initramfs-toybrick-2.0.img root=PARTUUID=614e0000-0000-4b53-8000-1d28000054a9 rw rootwait rootfstype=ext4
Retrieving file: /extlinux/toybrick.dtb
106116 bytes read in 52 ms (1.9 MiB/s)
"Synchronous Abort" handler, esr 0x96000010
* Relocate offset = 00000000f5bda000
* ELR(PC)    =   0000000000222cb8
* LR         =   0000000000222dfc
* SP         =   00000000f3dcb9b0

* ESR_EL2    =   0000000096000010
        EC[31:26] == 100101, Exception from a Data abort, from current exception level
        IL[25] == 1, 32-bit instruction trapped

* DAIF       =   00000000000003c0
        D[9] == 1, DBG masked
        A[8] == 1, ABORT masked
        I[7] == 1, IRQ masked
        F[6] == 1, FIQ masked

* SPSR_EL2   =   0000000040000349
        D[9] == 1, DBG masked
        A[8] == 1, ABORT masked
        I[7] == 0, IRQ not masked
        F[6] == 1, FIQ masked
        M[4] == 0, Exception taken from AArch64
        M[3:0] == 1001, EL2h

* SCTLR_EL2  =   0000000030c51835
        I[12] == 1, Icaches enabled
        C[2] == 1, Dcache enabled
        M[0] == 1, MMU enabled

* HCR_EL2    =   000000000800003a
* VBAR_EL2   =   00000000f5dda800
* TTBR0_EL2  =   00000000f7ff0000

x0 : 000000000a200000 x1 : 000000000000003a
x2 : 000000000a200000 x3 : 00000000f5e71710
x4 : 0000000000000010 x5 : 0000000000000000
x6 : 0000000000000010 x7 : 0000000000000044
x8 : 00000000f5ec3768 x9 : 0000000000000008
x10: 00000000f3e3e1a0 x11: 00000000f3dd9260
x12: 0000000000000000 x13: 0000000000000200
x14: 000000000000000e x15: 00000000ffffffff
x16: 00000000c683ff6f x17: 00000000c265984a
x18: 00000000f3dd1d10 x19: 00000000f5ec34e8
x20: 00000000f3dcbd00 x21: 0000000000800800
x22: 0000000000000016 x23: 00000000f5ec35e0
x24: 00000000f5ec35d8 x25: 00000000f3dcbd40
x26: 00000000f5ead3c8 x27: 0000000000000002
x28: 00000000f3e41f20 x29: 00000000f3dcbba0

SP:
f3dcb9b0:  00000000 00000000 00000000 00000000
f3dcb9c0:  00000000 00000000 f5e99af3 00000000
f3dcb9d0:  00000000 00000000 00000000 00000000
f3dcb9e0:  f5e99b3a 00000000 f5e99b60 00000000
f3dcb9f0:  f5e99bad 00000000 f5e99bfa 00000000
f3dcba00:  f5e99c3a 00000000 f5e99c7a 00000000
f3dcba10:  f5e99cb7 00000000 00000000 00000000
f3dcba20:  00000000 00000000 f5e99cf4 00000000
f3dcba30:  f3dcbba0 00000000 f5ddaa0c 00000000
f3dcba40:  f5ec34e8 00000000 0000000b 00000000
f3dcba50:  f7ff0000 00000000 0800003a 00000000
f3dcba60:  30c51835 00000000 f3dcb9b0 00000000
f3dcba70:  40000349 00000000 f5dda800 00000000
f3dcba80:  000003c0 00000000 96000010 00000000
f3dcba90:  f5dfccb8 00000000 0a200000 00000000
f3dcbaa0:  0000003a 00000000 0a200000 00000000


Call trace:
  PC:   [< 00222cb8 >]
  LR:   [< 00222dfc >]

Stack:
        [< 00222cb8 >]
        [< 00216058 >]
        [< 002086f0 >]
        [< 0020e8b4 >]
        [< 0020e9ec >]
        [< 0020ed48 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00215208 >]
        [< 00214954 >]
        [< 00214e24 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00214ce0 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00214ce0 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00214ce0 >]
        [< 00214ce0 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00214ce0 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00215208 >]
        [< 00214954 >]
        [< 00214e24 >]
        [< 00214ce0 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 00229794 >]
        [< 0022a1e0 >]
        [< 00215068 >]
        [< 00215208 >]
        [< 0021490c >]
        [< 002296e4 >]
        [< 002132f8 >]
        [< 00215e44 >]
        [< 0027a620 >]
        [< 00215fd0 >]
        [< 00201b2c >]

Copy above stack info to a file(eg. dump.txt), and
execute command in your U-Boot project: ./scripts/stacktrace.sh dump.txt

Resetting CPU ...

DDR Version 1.24 20191016
In
soft reset
SRX
Channel 0: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
CS = 1
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x82
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=32 Size=2048MB
Channel 1: LPDDR3, 800MHz
CS = 0
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
CS = 1
MR0=0x58
MR1=0x58
MR2=0x58
MR3=0x58
MR4=0x2
MR5=0x1
MR6=0x5
MR7=0x0
MR8=0x1F
MR9=0x1F
MR10=0x1F
MR11=0x1F
MR12=0x1F
MR13=0x1F
MR14=0x1F
MR15=0x1F
MR16=0x1F
Bus Width=32 Col=10 Bank=8 Row=15/15 CS=2 Die Bus-Width=32 Size=2048MB
256B stride
ch 0 ddrconfig = 0x101, ddrsize = 0x2020
ch 1 ddrconfig = 0x101, ddrsize = 0x2020
pmugrf_os_reg[2] = 0x3AA0DAA0, stride = 0xD
OUT
Boot1: 2019-03-14, version: 1.19
CPUId = 0x0
ChipType = 0x10, 310
SdmmcInit=2 0
BootCapSize=100000
UserCapSize=29820MB
FwPartOffset=2000 , 100000
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
mmc0:cmd8,20
mmc0:cmd5,20
mmc0:cmd55,20
mmc0:cmd1,20
SdmmcInit=0 1
StorageInit ok = 68658
SecureMode = 0
SecureInit read PBA: 0x4
SecureInit read PBA: 0x404
SecureInit read PBA: 0x804
SecureInit read PBA: 0xc04
SecureInit read PBA: 0x1004
SecureInit read PBA: 0x1404
SecureInit read PBA: 0x1804
SecureInit read PBA: 0x1c04
SecureInit ret = 0, SecureMode = 0

回复

使用道具 举报

008kai

注册会员

积分
115
26#
 楼主| 发表于 2022-2-22 11:29:28 | 只看该作者
zhangzj 发表于 2022-2-22 08:47
可以去掉,因为client和optee os版本不匹配了。
1. 把uboot中optee相关的宏disable掉
CONFIG_OPTEE_CLIEN ...

哥,您能不能写一个详细的移植optee的过程,我在这方面的水平不太行,不胜感激
回复

使用道具 举报

008kai

注册会员

积分
115
27#
 楼主| 发表于 2022-2-22 15:16:53 | 只看该作者
zhangzj 发表于 2022-2-22 08:47
可以去掉,因为client和optee os版本不匹配了。
1. 把uboot中optee相关的宏disable掉
CONFIG_OPTEE_CLIEN ...

大佬,如果论坛上回复不方便,可以通过邮箱请教,下面是我的邮箱:
yunyangxdu@163.com
回复

使用道具 举报

zhangzj

超级版主

积分
1117
28#
发表于 2022-2-22 19:15:21 | 只看该作者
uboot崩溃打印出来的堆栈下面有提示如何debug,根据提示操作可以打印出调用函数堆栈,trace到哪个函数崩溃

Copy above stack info to a file(eg. dump.txt), and
execute command in your U-Boot project: ./scripts/stacktrace.sh dump.txt
回复

使用道具 举报

008kai

注册会员

积分
115
29#
 楼主| 发表于 2022-2-22 20:14:34 | 只看该作者
zhangzj 发表于 2022-2-22 19:15
uboot崩溃打印出来的堆栈下面有提示如何debug,根据提示操作可以打印出调用函数堆栈,trace到哪个函数崩溃
...

SYMBOL File: ./u-boot.sym

Call trace:

Stack:
       [< 00216058 >]  bootm_find_images+0x40/0xd8
       [< 002086f0 >]  do_booti+0x134/0x194
       [< 0020e8b4 >]  label_boot+0x534/0x580
       [< 0020e9ec >]  handle_pxe_menu+0xec/0x174
       [< 0020ed48 >]  do_sysboot+0x1e4/0x1f4
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 00214954 >]  parse_string_outer+0xdc/0xf4
       [< 00214e24 >]  run_list_real+0x4b8/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 00214954 >]  parse_string_outer+0xdc/0xf4
       [< 00214e24 >]  run_list_real+0x4b8/0x72c
       [< 00214ce0 >]  run_list_real+0x374/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 00229794 >]  do_run+0x58/0x80
       [< 0022a1e0 >]  cmd_process+0xd8/0x10c
       [< 00215068 >]  run_list_real+0x6fc/0x72c
       [< 00215208 >]  parse_stream_outer+0x170/0x67c
       [< 0021490c >]  parse_string_outer+0x94/0xf4
       [< 002296e4 >]  run_command_list+0x38/0x90
       [< 002132f8 >]  main_loop+0x5c/0x6c
       [< 00215e44 >]  run_main_loop+0xc/0x10
       [< 0027a620 >]  initcall_run_list+0x58/0x94
       [< 00215fd0 >]  board_init_r+0x20/0x24
       [< 00201b2c >]  relocation_return+0x4/0x0
这。。。看不懂呀
回复

使用道具 举报

zhangzj

超级版主

积分
1117
30#
发表于 2022-2-23 09:02:26 | 只看该作者
uboot关掉AVB试看看
CONFIG_ANDROID_AVB=n
回复

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

产品中心 购买渠道 开源社区 Wiki教程 资料下载 关于Toybrick


快速回复 返回顶部 返回列表